3,4,5,6-Tetrahydrophthalic anhydride (CAS 2426-02-0, supplier designation TMMA) is the low-melting isomer of tetrahydrophthalic anhydride: the same C8H8O3 formula and the same 152.15 g/mol molecular weight as THPA, but with the ring double bond sitting against the anhydride ring instead of isolated in the ring. That single structural difference moves the melting point from about 100 deg C down to about 67 deg C, which is why this grade is bought wherever a lower melt temperature, a lower mix viscosity or a eutectic blend is wanted.
Basic Information
| CAS Number | 2426-02-0 |
| Synonyms | 3,4,5,6-Tetrahydrophthalic anhydride; TMMA (supplier designation); 1-cyclohexene-1,2-dicarboxylic anhydride |
| Molecular Formula | C8H8O3 |
| Molecular Weight | 152.15 g/mol |
| Anhydride groups per molecule | 1 |
| Anhydride equivalent weight | 152.15 g/eq (theoretical) |
| PubChem CID | 12475 |
| InChIKey | HMMBJOWWRLZEMI-UHFFFAOYSA-N |
| SMILES | C1CCC2=C(C1)C(=O)OC2=O |
| IUPAC name | 4,5,6,7-tetrahydro-2-benzofuran-1,3-dione |
| Appearance | Pale yellow to white flake or solid |
| Melting point | 66 to 69 deg C (specified 66 to 72 deg C on the 99% grade) |
| Chemical family | Cycloaliphatic dicarboxylic anhydride, unsaturated |
Specifications
| Item | Grade 1 | Grade 2 | Grade 3 (custom) |
|---|---|---|---|
| Appearance | Pale yellow flake | White or off-white solid | White solid |
| Assay | >=96.0% | >=99.0% | >=99.5% or >=99.8% |
| Melting point | 66 to 69 deg C | 66 to 72 deg C | On request |
| Typical use | Resin and polyester intermediate | General curing and intermediate work | High-purity curing, electrical and optical |
What the Three Grades Are For
The 96% grade is a chemistry feedstock, not a curing agent. A 96% assay means roughly 3 to 4% of the material is the corresponding diacid plus low-boiling oligomers, and that shows up as the pale yellow colour. For polyester, alkyd and plasticiser routes this is entirely acceptable: the diacid is a reactive species in those processes too, and colour is not critical.
The 99% grade is the practical curing grade. It is white to off-white, melts in the 66 to 72 deg C band, and gives a cured casting with a predictable colour. Where a formulator wants the lower melting point of the 3,4,5,6-isomer but is running a standard electrical or coatings recipe, this is the grade to specify.
The 99.5% and 99.8% custom grades serve high-purity work where residual acid and oligomer content have to be squeezed further, typically electrical insulation with tight dielectric requirements, optical or transparent castings, and applications where the anhydride is being used as a fine-chemical intermediate rather than as a bulk hardener.
The Low Melting Point, and What It Costs
Melting at about 67 deg C instead of about 100 deg C changes the plant around the material, not just the number on the certificate.
| Property | 3,4,5,6-THPA (this product) | 1,2,3,6-THPA | Practical consequence |
|---|---|---|---|
| Molecular formula | C8H8O3 | C8H8O3 | Identical formula and weight: only structure and physical constants separate them |
| Molecular weight | 152.15 | 152.15 | Equivalent weight is the same, so the dose calculation is the same |
| Melting point | 66 to 69 deg C | About 100 deg C | Lower melt temperature, shorter melting time, less thermal darkening |
| InChIKey | HMMBJOWWRLZEMI-UHFFFAOYSA-N | KMOUUZVZFBCRAM-UHFFFAOYSA-N | The only unambiguous identity check on a certificate |
The benefit is real: a melt tank can run at 80 to 90 deg C instead of 120 to 130 deg C, hold-up times shorten, and the colour drift that comes from hot holding is reduced. The cost is also real, and it is a logistics cost. A product that softens at 67 deg C will soften inside a container standing in the sun or inside a hot warehouse in summer, and it can arrive as a fused block or as a partially melted drum. Buyers in hot climates should specify the packing (bag inside a lined drum, or temperature-controlled container) and be prepared to re-melt before use.
Applications
- Epoxy curing agent where a low melt temperature matters. Casting shops that do not want to run a 130 deg C melt tank, and formulators who blend this isomer with a higher-melting anhydride to reach a eutectic mix with a workable melting range and a lower viscosity at the dosing temperature.
- Blend component for anhydride eutectics. Mixing isomers and homologues is standard practice because a blend can have a lower melting point than any of its components, which simplifies dosing and reduces the thermal exposure of the harder component.
- Unsaturated polyester and alkyd resin intermediate. The retained double bond participates in the copolymerisation with styrene, and the 96% grade is normally acceptable here.
- Plasticiser and ester intermediate through ring-opening with alcohols.
- Fine-chemical building block where the double bond conjugated with the anhydride ring offers a different reactivity pattern from the isolated double bond of 1,2,3,6-THPA.
Formulating With This Isomer
The dose is set by equivalents exactly as it is for the other tetrahydrophthalic isomer, because the equivalent weight is identical:
phr = (AEW / EEW) x 100 x r, with AEW = 152.15 and r = 0.85 to 1.0
| Resin EEW | r = 0.85 | r = 0.90 | r = 1.00 |
|---|---|---|---|
| 185 (standard DGEBA) | 69.9 phr | 74.0 phr | 82.2 phr |
| 200 | 64.7 phr | 68.5 phr | 76.1 phr |
| 250 | 51.7 phr | 54.8 phr | 60.9 phr |
Because the melting point is low, this isomer is often used as the liquid or low-melting part of an anhydride blend: it can be melted into the resin at a lower temperature and then the higher-melting component is dissolved into it, which shortens the total heat history of the mix compared with melting everything separately.
Handling and Storage
Keep the material sealed, dry and cool. The two failure modes are the same as for every anhydride: hydrolysis to the diacid, and thermal colour drift. Because the melting point is only about 67 deg C, store away from hot walls, steam lines and sun-exposed containers, and do not stack pallets in a place that reaches 60 deg C in summer.
Handle with local exhaust ventilation, gloves, eye protection and a dust mask. The material is a skin sensitiser and, once hydrolysed, is acidic and corrosive. Clean spills dry and dispose of them as anhydride, not as a water-washed solution.
Do not store next to amines, accelerators, alkalis or alcohols. The 96% grade has a higher acid content and is more aggressive to skin and to metal than the 99% grades, so the lower grades deserve the stricter handling discipline.
Packaging and Supply
Standard packing is 25 kg net in paper sacks with a polyethylene inner liner, on pallets, with 500 kg and 1,000 kg jumbo bags for bulk users. For hot-climate destinations we recommend a moisture-barrier liner and, where the journey involves long dwell times in the sun, a ventilated or insulated container. Each lot is supplied with a certificate of analysis stating assay, appearance and melting range, and for the custom grades the additional purity data agreed with the customer.
Chemical Structure
C1CCC2=C(C1)C(=O)OC2=O
Related Products
- 1,2,3,6-Tetrahydrophthalic anhydride (THPA), CAS 85-43-8
- Hexahydrophthalic anhydride (HHPA), CAS 85-42-7
- Methyltetrahydrophthalic anhydride (MTHPA), CAS 11070-44-3 – the liquid member, seven grades from Pt-Co 50 to 10.
- Methylhexahydrophthalic anhydride (MHHPA) on request
- Epoxy resins, accelerators and formulated casting systems on request
FAQ
Is TMMA the same product as THPA? No, and the naming is genuinely confusing. THPA usually refers to 1,2,3,6-tetrahydrophthalic anhydride (CAS 85-43-8, melting point about 100 deg C). This product is the 3,4,5,6-isomer (CAS 2426-02-0, melting point about 67 deg C), which some producers label TMMA. Always buy on CAS number and, for critical work, on InChIKey.
Can I substitute this for THPA in an existing formulation? Only after checking the cure schedule and the melt handling. The equivalent weight is identical, so the dose in phr does not change, but the melting point, the viscosity at dosing temperature and the double-bond reactivity all differ. Run a lab casting before switching a production recipe.
Why is the 96% grade yellow? Because the residual 3 to 4% is largely the diacid and low oligomers formed during manufacture. It is a chemistry feedstock grade, not a defect. If your process needs white material, specify the 99% grade.
Will the product melt in transit? It can. With a melting point near 67 deg C, a container in direct sun in summer can reach that. It does not damage the chemistry, but it changes the physical form, so plan for re-melting and check the free acid after arrival.
What is the difference between the 99.5% and 99.8% custom grades? The residual acid and oligomer content, and the resulting colour and dielectric behaviour. For most casting work 99.5% is sufficient; 99.8% is for applications where the anhydride is the purity-limiting component.
Contact PolyblueChem for a current certificate of analysis, a sample of the 99% or custom grade, and a quotation for bagged or jumbo bag supply.




