4-Methyl tetrahydrophthalic anhydride (MTHPA, CAS 11070-44-3) is a liquid cycloaliphatic dicarboxylic anhydride: a pale yellow to water-clear liquid at room temperature with a viscosity of 30 to 70 mPa.s at 25 deg C and a crystallisation point of either -15 deg C or 0 deg C depending on grade. It is the liquid member of the tetrahydrophthalic anhydride family, obtained by the Diels-Alder addition of isoprene to maleic anhydride rather than the butadiene route that gives solid THPA.
MTHPA is the working anhydride where a solid is inconvenient: electrical castings, potting and encapsulation, laminates and composite tooling. Because it is already liquid it needs no melt tank, no hot lines and no flaking, and because the anhydride group is diluted by a methyl group its equivalent weight is 9% higher than THPA’s, which changes the dose by about 15%.
Basic Information
| CAS Number | 11070-44-3 |
| CAS registry name | Tetrahydromethylphthalic anhydride (1,3-Isobenzofurandione, tetrahydromethyl-) |
| EINECS | 234-290-7 |
| Synonyms | MTHPA; 4-methyl-1,2,3,6-tetrahydrophthalic anhydride; tetrahydromethylphthalic anhydride; methylcyclohexene dicarboxylic anhydride |
| Molecular Formula | C9H10O3 |
| Molecular Weight | 166.17 g/mol |
| Anhydride groups per molecule | 1 |
| Anhydride equivalent weight | 166.18 g/eq theoretical; about 175.7 g/eq at an anhydride group content of 41.0% |
| Appearance | Pale yellow clear liquid to water-clear liquid, grade dependent |
| Viscosity at 25 deg C | 30 to 50 mPa.s, or 50 to 70 mPa.s, grade dependent |
| Crystallisation point | 0 deg C max, or -15 deg C max, grade dependent |
| Chemical family | Cycloaliphatic dicarboxylic anhydride, liquid |
| Isomer distribution | 3-methyl / 4-methyl = 65 +/- 5 / 35 +/- 5 (producer declaration) |
| PubChem CID / InChIKey | No single record. See the note below on why |
One CAS, Seven Grades, and Why That Is Not a Contradiction
The CAS number 11070-44-3 is registered as tetrahydromethylphthalic anhydride: a methyl-substituted tetrahydrophthalic anhydride with the methyl position left unspecified. A single positional isomer has its own CAS number – 4-methyl-1,2,3,6-tetrahydrophthalic anhydride is 3425-89-6 – and neither registration covers a fixed isomer ratio.
That is the whole explanation for the seven grades below. Commercial MTHPA is a mixture whose isomer distribution and residual tetrahydrophthalic anhydride content decide where the crystallisation point and the viscosity land. Two lots can carry the same CAS number, the same formula C9H10O3 and the same molecular weight 166.17, and still differ in crystallisation point by 15 deg C and in viscosity by a factor of two.
The practical consequence is short: a purchase specification that states only the CAS number does not define the product. Write the crystallisation point, the viscosity and the colour into the specification, or accept whatever the lot happens to be.
The isomer distribution behind the specifications on this page is declared by the producer at 3-methyl / 4-methyl = 65 +/- 5 / 35 +/- 5. It is a supplier declaration rather than a certificate line, and it is the number to compare when two offers diverge on crystallisation point or viscosity at the same CAS number.
Specifications
Three numbers are common to all seven grades. They are the ones a certificate is normally judged on, and they are also the ones that tell you whether the lot is fully anhydride rather than partly hydrolysed:
| Item | All grades |
|---|---|
| Anhydride group content | 40.5% min (grades 2, 4, 5) or 41.0% min (grades 1, 3, 6, 7) |
| Acid value | 640 to 685 mg KOH/g |
| Volatiles | 1.5% max |
The four numbers that actually select a grade are appearance, colour, viscosity, crystallisation point and free acid:
| Item | G1 | G2 | G3 | G4 light colour | G5 custom | G6 optoelectronic | G7 optoelectronic custom |
|---|---|---|---|---|---|---|---|
| Appearance | Pale yellow, clear | Pale yellow, clear | Pale yellow, clear | Colourless, clear | Colourless, clear | Colourless, clear | Colourless, clear |
| Colour, Pt-Co (Hazen) | – | – | – | 50 max | 20 or 30 max | 20 max | 10 max |
| Viscosity at 25 deg C, mPa.s | 30 to 50 | 30 to 50 | 50 to 70 | 30 to 50 | 30 to 50 | 30 to 50 | 30 to 50 |
| Crystallisation point | -15 deg C max | 0 deg C max | -15 deg C max | 0 deg C max | 0 deg C max | 0 deg C max | 0 deg C max |
| Anhydride group content | 41.0% min | 40.5% min | 41.0% min | 40.5% min | 40.5% min | 41.0% min | 41.0% min |
| Acid value, mg KOH/g | 640 to 685 | 640 to 685 | 640 to 685 | 640 to 685 | 640 to 685 | 640 to 685 | 640 to 685 |
| Volatiles | 1.5% max | 1.5% max | 1.5% max | 1.5% max | 1.5% max | 1.5% max | 1.5% max |
| Free acid | 0.5% max | 0.5% max | 0.5% max | 0.5% max | 0.1 or 0.2% max | 0.5% max | 0.1 or 0.2% max |
Which Grade to Take
- G1 – the standard low-crystallising grade. Crystallisation point -15 deg C and viscosity 30 to 50 mPa.s. This is the grade that stays liquid in an unheated store through a cold winter, and it is the default for general casting and potting where colour is not specified.
- G2 – the standard grade with a 0 deg C floor. Same viscosity, higher crystallisation point, lower anhydride group minimum (40.5%). Cheaper where the material is kept indoors and the plant never sees sub-zero nights.
- G3 – the high-viscosity grade. 50 to 70 mPa.s with the low crystallisation point of G1. Higher viscosity is wanted when the system carries filler and settles slowly, or when a thicker film is being applied per pass.
- G4 – light colour. Colourless liquid with a Pt-Co figure of 50 max. The step up from the pale yellow grades, and the first grade where a colour number rather than a description is quoted.
- G5 – custom light colour. Pt-Co 20 or 30 max with free acid down to 0.1 or 0.2%. The bridge between general and electronic grades.
- G6 – optoelectronic grade. Pt-Co 20 max, 41.0% anhydride group minimum, free acid 0.5% max. For visible parts and light-carrying parts where the cured colour matters.
- G7 – optoelectronic grade, custom. Pt-Co 10 max with free acid 0.1 or 0.2% max. The tightest combination offered: colour and hydrolysis both held at the level needed for optical encapsulation.
Anhydride Group Content and Acid Value Are the Same Number
The anhydride group C2O3 weighs 72.02 g/mol, so the theoretical anhydride group content of a pure 166.17 g/mol MTHPA is 72.02 / 166.17 = 43.34%. A specification of 41.0% min therefore corresponds to an active content of 41.0 / 43.34 = 94.6%, which is an equivalent weight of 166.18 / 0.946 = 175.7 g/eq rather than the 166.18 printed on every data sheet.
The acid value carries the same information from the other direction. One anhydride group consumes two equivalents of potassium hydroxide, so the theoretical acid value is 2 x 56.106 / 166.17 x 1000 = 675.4 mg KOH/g. The 640 lower limit is 640 / 675.4 = 94.8% of theory – the same 94.6% that the anhydride group specification states, which is what a consistent specification looks like.
Two warnings follow from the same arithmetic. The 685 upper limit is 101.4% of theory, so it cannot be read as a purity ceiling; it is the top of a titration window and nothing more. And a grade quoted at 40.5% min cannot simultaneously be at 40.5% and at the 640 acid value floor, because 40.5% of theory works out to an acid value of about 631. When a certificate shows both numbers at once, one of them is rounded.
Applications
- Epoxy casting and encapsulation. Dry-type transformers, instrument transformers, bushings and insulators, where a liquid anhydride allows vacuum casting without a melt stage. Low exotherm, low shrinkage and high glass transition are the reasons anhydride cure dominates thick-section electrical parts.
- Potting of electronic assemblies. Power modules, ignition coils, sensors and automotive electronics. The liquid form fills fine gaps and the long pot life suits multi-part dispensing.
- LED and optical encapsulation. With cycloaliphatic epoxy resins, where colour after cure and resistance to yellowing matter as much as the mechanical properties. This is what grades G6 and G7 are specified for.
- Laminates and prepregs. A liquid anhydride can be formulated into solvent-free or low-solvent impregnating systems for electrical laminates.
- Composite tooling and filament winding. Long gel times and low viscosity at ambient temperature make MTHPA systems workable for large parts without a heated melt line.
Formulating With MTHPA
The dose is set by equivalents:
phr = (AEW / EEW) x 100 x r
where AEW is the anhydride equivalent weight, EEW the epoxy equivalent weight of the resin, and r the anhydride-to-epoxy ratio, usually 0.85 to 1.00. Using the worst-case AEW of 175.7 that a 41.0% minimum grade allows:
| Resin EEW | r = 0.85 | r = 0.90 | r = 1.00 |
|---|---|---|---|
| 185 (standard DGEBA) | 80.7 phr | 85.4 phr | 95.0 phr |
| 200 | 74.7 phr | 79.1 phr | 87.9 phr |
| 250 | 59.7 phr | 63.3 phr | 70.3 phr |
Compare that with solid THPA, which needs 74.0 phr at EEW 185 and r = 0.90. The ratio is 85.4 / 74.0 = 1.154: switching from THPA to MTHPA changes the dose by about 15%, not by the 1.3% that separates THPA from HHPA. A formulation transferred from a solid anhydride without recalculating will be 13% under-cured.
If the dose is calculated from the theoretical 166.18 but the lot sits at the 41.0% floor, the calculated figure – 80.9 phr at EEW 185 and r = 0.90 – is 5.3% below the 85.4 phr that lot actually needs. That is the reason to calculate the dose from the certificate’s anhydride group content rather than from the family name.
Handling and Storage
MTHPA is supplied as a liquid in drums and requires no melting, which removes the two failure modes of the solid grades – overheated melt tanks and wet melt lines. It does not remove moisture sensitivity. The liquid has a larger exposed surface per unit volume than flake in a sealed bag, so every drum opening is an exchange with the air in the plant.
Three practical rules. Keep drums closed and, for the low free-acid grades, blanketed with dry nitrogen after partial use. Store above the crystallisation point: a G2 drum at 0 deg C max will crystallise in an unheated store in winter, and crystallisation is reversible but each re-melt is a heat history that moves colour. Do not re-melt with an open flame or a high-temperature band heater; use a controlled oven or drum heater at the lowest workable temperature, and homogenise after melting, because the crystallised fraction and the liquid fraction are not the same composition.
Segregate from amines, alkalis, alcohols and water. Handle with gloves and eye protection; the anhydride is a skin sensitiser and the hydrolysed material is corrosive.
Packaging and Supply
Supplied in steel drums, with IBC and bulk options for volume users; drum size and lining details on request. Each lot ships with a certificate of analysis covering appearance, colour, viscosity, crystallisation point, anhydride group content, acid value, volatiles and free acid. The isomer ratio is declared at 3-methyl / 4-methyl = 65 +/- 5 / 35 +/- 5. Chloride is not a routine certificate line, but it is reported on request: the figure for the current production is below 2 ppm. Other ion data are measured on request. A safety data sheet accompanies the first shipment of each grade.
Related Products
- 1,2,3,6-Tetrahydrophthalic anhydride (THPA), CAS 85-43-8
- 3,4,5,6-Tetrahydrophthalic anhydride (TMMA), CAS 2426-02-0
- Hexahydrophthalic anhydride (HHPA), CAS 85-42-7
- MTHPA grades: how to choose between the seven specifications
- Anhydride curing agent dosage: phr, AEW and accelerators
- Electronic and optoelectronic grade MTHPA
- Methylhexahydrophthalic anhydride (MHHPA), CAS 25550-51-0 – the hydrogenated analogue, no ring double bond
FAQ
Is MTHPA the same as THPA? No. THPA is C8H8O3 with a molecular weight of 152.15 and is a solid that melts near 100 deg C. MTHPA carries an extra methyl group, is C9H10O3 at 166.17, and is a liquid at room temperature. The equivalent weights differ by 9% and the practical dose by about 15%.
Why do two suppliers quote the same CAS with different crystallisation points? Because 11070-44-3 is registered as tetrahydromethylphthalic anhydride without a specified methyl position, so the number does not fix the isomer ratio. The crystallisation point and the viscosity are what actually define the grade.
What is the difference between MTHPA and MHHPA? MHHPA is the hydrogenated analogue – methylhexahydrophthalic anhydride, a different CAS and a different formula – with no ring double bond, lower viscosity and better colour stability. MTHPA retains one double bond, which is why it can yellow under heat and UV where MHHPA does not.
Can MTHPA cure epoxy at room temperature? Not in production. Anhydride cure needs heat, typically 120 to 160 deg C with an accelerator and a post-cure step; the advantage over amine cure is the low exotherm that allows thick sections to be cured without runaway.
Does the grade affect the cure schedule? Only through the equivalent weight. A 40.5% grade needs about 1.2% more anhydride than a 41.0% grade at the same r, which is inside most formulation tolerances. The grade choice matters far more for logistics, colour and free acid than for cure kinetics.
Contact PolyblueChem for a current certificate of analysis, a sample of any grade, and a quotation for drum, IBC or bulk supply.




