5,5′-Methylenebis(isobenzofuran-1,3-dione) (CAS 4200-79-7), also written methylenediphthalic dianhydride, is two phthalic anhydride units joined through a single methylene bridge. It is the dianhydride you reach for when PMDA is too rigid and too dark: the same two anhydride rings, a much more flexible hinge in the middle, and no fused aromatic system driving colour.
Status: Specification below is the current production grade. Assay, acid value and water content are reported per lot; ask for a COA before fixing a stoichiometry.
Basic Information
| CAS Number | 4200-79-7 |
| Chemical name | 5,5′-Methylenebis(isobenzofuran-1,3-dione); 4,4′-methylenediphthalic anhydride; methylenebis(phthalic anhydride) |
| Molecular Formula | C17H8O6 |
| Molecular Weight | 308.24 g/mol |
| PubChem CID | 513913 |
| InChIKey | IKPDWXPKZUEPFR-UHFFFAOYSA-N |
| Chemical Family | Bis(phthalic anhydride), methylene bridged |
| Anhydride groups per molecule | 2 |
| Anhydride equivalent weight | 154.12 g/eq |
Specification
| Item | Requirement |
| Appearance | White to pale yellow solid |
| Purity (assay) | 99% min |
| Anhydride equivalent weight | 154.12 g/eq (308.24 / 2) |
| Acid value, after hydrolysis | 364.1 mg KOH/g theoretical (4 carboxyl equivalents) |
| Anhydride groups | 2, on separate rings joined by a CH2 bridge |
What the methylene bridge buys you
The bridge is the whole point. Two rigid phthalic anhydride units connected by a single CH2 can rotate relative to one another, and that rotation propagates into the polymer:
- Flexibility without aliphatic rings. A polyimide built on this dianhydride is less brittle than a PMDA-based one, keeps more of the aromatic thermal stability than a fully alicyclic dianhydride, and can be pushed toward thermoplastic behaviour.
- Solubility. The non-planar linkage disrupts chain packing, which raises solubility in polar aprotic solvents – the practical entry point for solution-cast films and coatings.
- Colour. The anhydride rings are still aromatic, so films are not water-white the way an alicyclic dianhydride gives; expect pale amber rather than brown.
- Equivalent weight. At 154.12 g/eq the charge is about 40% of a PMDA charge per equivalent, but you are buying 308 g/mol of molecule to get two rings back – the economics follow the bridge, not the equivalents.
Comparison: bridge length and bridge chemistry
| Dianhydride | CAS | Formula / MW | AEW | Bridge | Effect |
| PMDA | 89-32-7 | C10H2O6 / 218.12 | 109.06 | Fused rings, no bridge | Maximum rigidity, amber film, low cost |
| Methylenebis(phthalic anhydride) | 4200-79-7 | C17H8O6 / 308.24 | 154.12 | -CH2- | Flexible hinge, improved solubility |
| Ethylidenebis(phthalic anhydride) | 22197-42-8 | C18H10O6 / 322.27 | 161.14 | -CH(CH3)- | One carbon longer plus a side methyl: more soluble, less crystalline |
| ODPA (oxydiphthalic anhydride) | 1823-59-2 | C16H6O7 / 310.21 | 155.11 | -O- | Ether hinge, good melt flow, high cost |
| BPADA (bisphenol A dianhydride) | 38103-06-9 | C31H24O8 / 524.5 | 262.2 | Bisphenol A unit | Thermoplastic PI, very high cost |
| HPMDA | 2754-41-8 | C10H8O6 / 224.17 | 112.09 | Fused alicyclic | Colour-stable, no aromatic absorption |
The useful comparison inside this table is the middle three rows. A methylene bridge, an ethylidene bridge and an ether bridge all do the same job – break the conjugation and let the chain bend – and they trade crystallinity against cost. The methylene version is the least expensive of the three and the most crystalline, which is why it handles as a solid powder and needs a solvent that can dissolve it completely.
Where it is used
| Application | Role | Note |
| Polyimide films and coatings | Flexible dianhydride for pale, tough films | Imidisation releases water – ramp slowly on thick films |
| Soluble polyimides | Non-planar bridge improves solubility in NMP/DMAc | Dry the solvent rigorously; the dianhydride hydrolyses |
| Epoxy curing | High crosslink density: 75.0 phr at EEW 185, r = 0.9 | Brittle alone; blend with a flexible anhydride |
| Polyester and alkyd modification | Two anhydride rings give a fast half-ester | Watch gelation at high functionality |
Handling, packaging and supply
The dianhydride hydrolyses: keep containers closed, store cool and dry, and let cold drums equilibrate before opening. Preferred pack is 25 kg net fibre drum with double polyethylene liner under nitrogen; 1 kg sample packs ship with desiccant. COA covers appearance, assay and acid value; water and metal content on request. Export classification normally follows HS 2917.20.
FAQ
How is this different from PMDA? Same two anhydride rings, but joined by a CH2 bridge rather than fused into one aromatic core. That gives flexibility and solubility, and costs some heat resistance and some colour.
What is the phr for epoxy? 75.0 phr at EEW 185 with r = 0.9 (154.12 / 185 x 100 x 0.9). Add an accelerator and expect a brittle, high-Tg network unless it is blended.
Why does the powder cake in the drum? Moisture. The acid value after hydrolysis should read 364.1 mg KOH/g on a good lot; a lower figure means rings have already opened.
Contact PolyBlueChem for a lot COA, a nitrogen-purged sample and a quotation against your volume and destination port.
Related reading
- The anhydride family map: every product, the AEW scale and the identification traps
- Anhydride curing agent dosage: phr from AEW and EEW
- Pyromellitic dianhydride (PMDA): properties, production and applications
- Free acid, colour and storage: what hydrolysis does to an anhydride




