Anhydrides are bought by name and by specification, but they are chosen by structure. Two products with equivalent weights within 3% of each other can behave completely differently in a pot, because one carries an aromatic ring and the other does not, or because one is saturated and the other yellows in service. This page is the family map: every anhydride on the site, sorted by what it actually is, with the one analytical test that separates each confusing pair.
The family, sorted by structure rather than by CAS
| Family | Members | What defines it |
| Simple alicyclic mono-anhydrides | THPA, TMMA, HHPA, MTHPA, MHHPA, 4-MHHPA | Six-membered ring, one anhydride; liquid or low-melting solid; the workhorses of electrical casting |
| Bridged bicyclic anhydrides | Nadic anhydride (826-62-0), norbornane-2,3-dicarboxylic anhydride (mixed endo/exo and pure endo), MNA, H-MNA | Norbornane skeleton; unsaturation decides colour stability, not the anhydride |
| Alkenyl succinic anhydrides | SA, OSA, NSA, DDSA, DSA, allylsuccinic anhydride, DCSA | Succinic core with an alkyl or alkenyl chain; MW = 14n + 98 for the unsaturated series |
| Aromatic mono-anhydrides and acids | Phthalic anhydride, trimellitic anhydride | Cheap, rigid, colour-forming; TMA carries one anhydride and one acid |
| Cycloaliphatic multi-anhydrides | HPMDA, 1,2,4-cyclohexanetricarboxylic anhydride | Hydrogenated aromatic cores; two anhydrides or anhydride-plus-acid on an alicyclic ring |
| Aromatic dianhydrides and bridged bis-anhydrides | PMDA, methylenebis(phthalic anhydride), ethylidenebis(phthalic anhydride) | Two anhydride rings; bridge chemistry sets flexibility, colour and cost |
| Functionalised anhydrides | Methacrylic anhydride, 4-ethynylphthalic anhydride, allylsuccinic anhydride | The anhydride is a tool for installing another reactive group, not the cure itself |
| Related non-anhydrides often filed here | Hydrogenated bisphenol A (a diol), dodecenylsuccinic acid (a diacid) | Dosed against hydroxyl or acid value, not anhydride equivalent weight |
The one-number scale: anhydride equivalent weight
Every dose in the family comes from the same formula – phr = AEW / EEW x 100 x r – so a table of AEW values is also a table of dose, at least at fixed resin and ratio. The figures below are theoretical, at the stated assay, against EEW 185 and r = 0.9.
| Product | CAS | MW | AEW used | phr at EEW 185, r 0.9 | eq per kg |
| Succinic anhydride | 108-30-5 | 100.07 | 100.6 at 99.5% | 48.9 | 9.94 |
| 1,2,4-Cyclohexanetricarboxylic anhydride | 53611-01-1 | 198.17 | 99.09 (anhydride + acid) | 48.2 | 10.09 |
| Pyromellitic dianhydride | 89-32-7 | 218.12 | 109.06 (2 rings) | 53.1 | 9.17 |
| HPMDA | 2754-41-8 | 224.17 | 112.09 (2 rings) | 54.5 | 8.92 |
| Allylsuccinic anhydride | 7539-12-0 | 140.14 | 140.14 | 68.2 | 7.14 |
| Methylenebis(phthalic anhydride) | 4200-79-7 | 308.24 | 154.12 (2 rings) | 75.0 | 6.49 |
| Ethylidenebis(phthalic anhydride) | 22197-42-8 | 322.27 | 161.14 (2 rings) | 78.4 | 6.21 |
| Nadic anhydride | 826-62-0 | 164.16 | 164.16 | 79.9 | 6.09 |
| Norbornane-2,3-dicarboxylic anhydride | none assigned | 166.17 | 166.17 | 80.8 | 6.02 |
| 4-MHHPA | 19438-60-9 | 168.19 | 169.9 at 99% | 82.7 | 5.89 |
| HHPA | 85-42-7 | 154.16 | 154.16 | 75.0 | 6.49 |
| MHHPA | 25550-51-0 | 168.19 | 171.6 at 98% | 83.5 | 5.83 |
| MTHPA | 11070-44-3 | 166.17 | 175.7 at 41% isomer basis | 85.4 | 5.69 |
| Methyl Nadic anhydride | 25134-21-8 | 178.18 | 181.8 at 98% | 88.5 | 5.50 |
| Hydrogenated MNA | 39973-36-9 | 180.20 | 180.20 | 87.7 | 5.55 |
| THPA / TMMA | 85-43-8 / 2426-02-0 | 152.15 | 152.15 | 74.0 | 6.57 |
| Dodecenylsuccinic anhydride | 26544-38-7 | 266.38 | 269.1 at 99% | 130.9 | 3.72 |
Read the table by family, not by size. The three large dianhydrides and the two multi-anhydrides sit at the bottom of the phr column even though their molecules are heavy, because one mole carries two rings. The alkenyl succinic anhydrides sit at the top because one heavy molecule carries one ring. If a formulation change moves a product from one family to another, the dose can move by a factor of two and a half – and the network properties change even more.
Five selection axes that decide more than price
| Axis | Question | What it removes |
| Saturation | Will the part be exposed to light, heat or colour-critical service? | Rules out every unsaturated ring – iodine value above 1 means yellowing is on a timer |
| State | Can the plant melt and hold a solid, or does it need a pumpable liquid? | Rules out solid hardeners for room-temperature impregnation |
| Equivalent weight | Is a high or low crosslink density wanted, and what pot life results? | Rules out the very low-AEW products where flexibility matters |
| Functionality beyond the anhydride | Is the acid, the alkenyl chain, the alkyne or the methacrylate actually needed? | Rules out mono-functional hardeners for dual-cure systems |
| Hydrolysis sensitivity | How dry is the process, and how is the material stored? | Rules out dianhydrides in a wet solvent process |
The identification traps, all in one table
These pairs are the ones that get substituted by mistake. In every case the physical constants overlap and one analytical number separates them.
| Pair | How they look alike | The test that separates them |
| TMMA (2426-02-0) / MTHPA (11070-44-3) / MHHPA (25550-51-0) | All liquid, all “methyl tetrahydro” or “methyl hexahydro” on a spec sheet | Hydrogenation level: iodine value 166.8 theoretical (TMMA) down to zero (MHHPA) |
| Nadic anhydride (826-62-0) / norbornane-2,3-dicarboxylic anhydride (no CAS) | Same skeleton, melting points within a few degrees of each other for the endo grade | Iodine value: 154.6 against 0 |
| DDSA (26544-38-7) / DSA (no single CAS) | Same trade abbreviation, MW differing by 2.01, dose differing by 0.7% | Iodine value: 95.3 against 0 |
| Succinic (108-30-5) / maleic anhydride (108-31-6) | One digit apart in CAS, both C4 anhydrides | Melting point and iodine value: 119 degC / zero against 52 degC / 259 theoretical |
| HPMDA (2754-41-8) / PMDA (89-32-7) | AEW within 3%, same dianhydride topology | Backbone: alicyclic gives colourless film, aromatic gives amber; no test substitutes for knowing which you bought |
| Methylene- (4200-79-7) / ethylidenebis anhydride (22197-42-8) | Same name shape, 14.03 g/mol apart | Molecular weight and melting behaviour; they are not grades of one product |
| Methacrylic anhydride (760-93-0) / a curing anhydride | Both called “anhydride”, both react with hydroxyls | Purpose: it installs a methacrylate group, it does not cure epoxy |
| HBPA (80-04-6) / bisphenol A (80-05-7) | One digit apart, both “bisphenol” | It is a diol, not an anhydride – dose against hydroxyl value, not AEW |
Reading the three lines that matter on a COA
- Iodine value settles saturation – the single most useful number in the family, because colour lies and assay is blind to it. Zero (or a few tenths) means saturated; a figure near the theoretical maximum means the ring double bond is intact.
- Free acid or acid value settles hydrolysis. Each product has a theoretical acid value after hydrolysis; a reading below it means rings have already opened. For the anhydride-acid hybrids such as 1,2,4-cyclohexanetricarboxylic anhydride, ask for both the direct and the hydrolysed value – the gap is the free-acid content.
- Water is the cause behind the other two. One kilogram of water per tonne of hardener consumes 55.5 mol of anhydride – about 5.6 kg of succinic anhydride, 9.2 kg of MTHPA, or nearly 15 kg of DDSA. That is why storage and packaging are part of the specification, not an afterthought.
Where to start, by process
| If you are | Start with | Read next |
| Casting electrical parts at room temperature | MTHPA or MHHPA (liquid, low colour), H-MNA where colour stability is critical | Liquid anhydride hardeners for electrical casting |
| Making a colourless or light-stable part | Saturated only: HHPA, MHHPA, H-MNA, norbornane anhydride, HPMDA | Free acid, colour and storage |
| Needing flexibility in a cured epoxy | DDSA or OSA (long alkenyl chain), blended with a rigid hardener | The alkenyl succinic anhydride chain-length guide |
| Building a polyimide | PMDA for heat and cost, HPMDA for colour, bridged bis-anhydrides for solubility | PMDA properties and applications |
| Installing a second cure mechanism | Allylsuccinic anhydride (peroxide), 4-ethynylphthalic anhydride (thermal alkyne), methacrylic anhydride (radical) | Anhydride curing agent dosage |
| Working out a dose for the first time | Any product page for its AEW, then the phr calculator article | Anhydride curing agent dosage: phr from AEW and EEW |
Related reading
- Alicyclic and aromatic dianhydrides: choosing the polyimide backbone
- Bridged bis-anhydrides compared: methylene, ethylidene, ether and bisphenol A
- Terminal alkyne anhydrides: 4-ethynylphthalic anhydride versus PEPA
- Methacrylation routes compared: anhydride, acid, acid chloride, glycidyl
- Anhydride curing agent dosage: how to calculate phr from AEW and EEW
- Free acid, colour and storage: what hydrolysis does to an anhydride
- Tetrahydro versus hexahydro phthalic anhydride: the isomer comparison
- Liquid anhydride hardeners for electrical casting
- MTHPA versus MHHPA: tetrahydro or hexahydro
- Alkenyl succinic anhydrides: chain length, dose and identity
- Succinic, maleic and glutaric anhydride compared
Every product in the family
- THPA (CAS 85-43-8) – TMMA (CAS 2426-02-0) – HHPA (CAS 85-42-7)
- MTHPA (CAS 11070-44-3) – MHHPA (CAS 25550-51-0) – 4-MHHPA (CAS 19438-60-9)
- Nadic anhydride (CAS 826-62-0) – Norbornane anhydride, endo/exo mixture (no CAS) – endo-Norbornane anhydride (no CAS)
- MNA (CAS 25134-21-8) – H-MNA (CAS 39973-36-9)
- Succinic anhydride (CAS 108-30-5) – OSA (CAS 42482-06-4) – NSA (CAS 28928-97-4)
- DDSA (CAS 26544-38-7) – DSA, branched (no CAS) – ASA 2024 (CAS 70983-53-8) – Allylsuccinic anhydride (CAS 7539-12-0)
- Phthalic anhydride (CAS 85-44-9) – Trimellitic anhydride (CAS 552-30-7)
- PMDA (CAS 89-32-7) – HPMDA (CAS 2754-41-8) – 1,2,4-Cyclohexanetricarboxylic anhydride (CAS 53611-01-1)
- Methylenebis(phthalic anhydride) (CAS 4200-79-7) – Ethylidenebis(phthalic anhydride) (CAS 22197-42-8)
- 4-Ethynylphthalic anhydride (CAS 73819-76-8) – Methacrylic anhydride (CAS 760-93-0)
- Hydrogenated bisphenol A (CAS 80-04-6) – Dodecenylsuccinic acid (CAS 29658-97-7)
If you are choosing between two families and the table above does not settle it, send the application: cure schedule, part thickness, colour target and the resin you already buy. We will answer with the two or three products that fit and the analytical line to check on each.