Alkenylsuccinic Anhydride (ASA 2024), Paper Sizing Grade, CAS: 70983-53-8

ASA 2024 (CAS 70983-53-8) is an alkenylsuccinic anhydride supplied as a paper sizing agent: a light brown to brown liquid with a declared content of 85% minimum. It is the reactive sizing chemistry for neutral and alkaline papermaking, applied as a freshly prepared emulsion so that the anhydride ring can esterify the cellulose surface inside the dryer section.

This is a different product from the other alkenylsuccinic anhydrides on this site, and the difference is not chain length – it is the application. The DDSA, DSA, OSA and NSA grades are sold as epoxy hardeners and chemical intermediates against an assay and a colour. A sizing grade is sold against what it does to paper: how fast it emulsifies, how long the emulsion survives, how much size is retained on the fibre and how much foam and deposit it leaves behind. Those are performance specifications, and they are what the 85% figure and the tight control of hydrolysis products are protecting.

Basic Information

CAS Number 70983-53-8
Chemical name Alkenylsuccinic anhydride (manufacturing-grade CAS; chain distribution supplier-specific)
Synonyms ASA; ASA 2024; alkenyl succinic anhydride; ASA sizing agent; alkenylsuccinic anhydride sizing emulsion
Molecular formula Not definable for the grade – the product is a distribution of chain lengths
PubChem record None for this CAS; it is a mixture-grade registration, not a single structure
Reactive group One anhydride ring per molecule
Appearance Light brown to brown liquid
Assay 85% min declared active content
Chemical family Alkenylsuccinic anhydride, paper sizing grade
Application Internal and surface sizing of neutral and alkaline paper and board

Specifications

Item Value
Appearance Light brown to brown liquid
Assay (active content) 85% min
Hydrolysis products, colour, viscosity Controlled and reported per lot; limits agreed against the machine

The 85% figure is the declared active anhydride content; the balance is carrier and is supplier-specific. Ask what the carrier is, because it decides how the product emulsifies and whether it is compatible with the cationic starch or synthetic retention chemistry already on the machine. A sizing agent is not a drop-in: the emulsion recipe and the addition point are part of the product.

How ASA Sizing Works

Cellulose is hydrophilic because of its surface hydroxyls. An alkenylsuccinic anhydride reacts with those hydroxyls to form an ester, and the long alkenyl chain that comes with the ester turns the surface hydrophobic. The reaction needs heat, which is why the sizing is developed in the dryer section and not at the wet end.

Three practical rules follow from that mechanism, and all three are the reason ASA is handled the way it is:

  • The anhydride must arrive at the fibre unhydrolysed. Once the ring has opened, the molecule is a diacid, it no longer esterifies, and it is a surface-active nuisance that generates foam and deposit instead of size.
  • The emulsion is made on site, immediately before use. ASA is not water-soluble, so it is emulsified with a cationic stabiliser – typically a cationic starch or a synthetic polymer – in a dedicated emulsification unit, and the resulting dilute emulsion has a working life measured in minutes to a few hours, not days.
  • The addition point is chosen for mixing, not for convenience. The emulsion has to be delivered to the fibre before it hydrolyses, which is why the point is downstream of the fan pump and why the whole loop is sized for a short residence time.

ASA Against AKD

The two reactive sizes dominate neutral papermaking, and the choice between them is a machine decision rather than a chemistry preference:

Item ASA AKD
Chemical type Alkenylsuccinic anhydride Alkyl ketene dimer
Reactive group Anhydride ring Lactone (ketene dimer)
Supply form Anhydride liquid, emulsified on site Often supplied as a stabilised emulsion or solid
Storage stability of the size Poor once emulsified – hydrolyses in minutes Good; emulsions are storage-stable
Sizing development Fast; largely in the dryer section Slow; full cure takes days
Machine requirement Emulsification unit, tight residence time control None beyond normal dosing
Typical limitation Hydrolysis, foam and deposit if the emulsion is stale Slower cure, and slippage / friction issues on some grades

The trade is straightforward. ASA gives fast, full sizing with fewer downstream handling issues, at the cost of a piece of equipment and a discipline that cannot be relaxed. AKD gives operational simplicity, at the cost of cure time and a different set of paper-machine problems. Mills that run both usually do so because their grade mix needs both behaviours, not because one is better.

Reading a Sizing Certificate

A certificate for a sizing grade carries different figures from an epoxy hardener certificate, and this is where buyers get caught:

Figure Why the mill asks for it
Active content The dose and the emulsion recipe are both calculated from it – 85% min here
Hydrolysis products, as the corresponding diacid Pre-hydrolysed material does not size; it foams and deposits
Colour A sizing agent ends up on white paper; brown streaks are a defect
Viscosity Decides whether the emulsification unit can handle the feed at temperature
Free maleic anhydride or unreacted feedstock Both are irritants and both affect the emulsion; ask whether they are controlled

The iodine value, which is the key identity figure for the epoxy-grade alkenylsuccinic anhydrides on this site, is not normally the deciding number here. A sizing grade is bought on performance, and the performance is measured on the machine – Cobb value, Hercules size test, or the mill’s own specification.

Handling, Storage and Emulsification

The neat product is a liquid in steel drums, IBCs and road tankers, stored indoors away from moisture, heat and direct sunlight. It is far more moisture-sensitive than the other members of this family because the sizing operation depends on the ring arriving intact: a drum that has taken up water will emulsify poorly and size unevenly, and the problem will not be visible in the drum.

Emulsification practice, in outline: heat the neat ASA moderately, prepare the stabiliser solution (cationic starch cooked to a clear solution, or the synthetic equivalent), combine under controlled shear in the emulsification unit, and dilute to the application solids. The emulsion is used within the working life stated by the supplier, and any unused emulsion is disposed of rather than held. The unit is flushed at the end of the campaign; dried ASA in a line is a deposit source.

Handling: the neat anhydride is an irritant and a skin sensitiser, and hydrolyses on contact with water or moist skin. Gloves, eye protection, local exhaust ventilation at the transfer point. The emulsion is a slip hazard. Absorb spills and dispose of as chemical waste; never wash the neat product into a drain, because it will hydrolyse and the resulting diacid is a persistent foam source in a treatment plant.

Chemical Behaviour

An alkenylsuccinic anhydride is a five-membered anhydride ring carrying a long alkenyl chain. The ring is the reactive group that bonds to cellulose; the chain is what makes the sized surface hydrophobic. The chain length distribution in a sizing grade is chosen for the balance between hydrophobic efficiency and emulsifiability, and is supplier-specific – ask for it if the machine is sensitive to it.

Related Products

FAQ

What is ASA 2024? An alkenylsuccinic anhydride sold as a paper sizing agent, CAS 70983-53-8, with a declared active content of 85% minimum. The CAS is a mixture-grade registration; there is no single molecular structure or PubChem record for the grade.

Can it be used as an epoxy hardener? Technically the chemistry is the same as the epoxy-grade alkenylsuccinic anhydrides, but a sizing grade is not sold or qualified against an epoxy equivalent weight, and its chain distribution is chosen for paper. Buy the epoxy grades – DDSA, DSA, OSA or NSA – for curing.

Why must the emulsion be fresh? Because the anhydride ring hydrolyses quickly in water, and hydrolysed material cannot esterify cellulose. A stale emulsion sizes poorly and generates foam and deposit. Emulsify on site and use within the supplier’s stated working life.

ASA or AKD? ASA sizes faster and avoids some of the friction issues of AKD, but it needs an emulsification unit and strict residence-time discipline. AKD is more forgiving in storage and dosing but cures slowly. The choice is a machine decision.

What does the 85% content mean? Declared active anhydride content; the balance is carrier, and the carrier is supplier-specific. Confirm what it is before changing supplier, because the emulsion recipe depends on it.

How is it shipped? Neat liquid in steel drums, IBCs and road tankers, kept dry. Do not accept a drum with a broken seal for a sizing application – the failure will show up on the machine, not in the drum.

Contact PolyBlueChem for a current certificate of analysis, a sample and an emulsification trial, and a quotation for drum, IBC or tanker supply.

Scroll to Top