Dodecenylsuccinic anhydride (DDSA, CAS 26544-38-7) is a C16 alkenyl succinic anhydride: a dodecenyl chain carrying one double bond, attached to the same five-membered anhydride ring as succinic anhydride. Formula C16H26O3, molecular weight 266.38. It is a pale yellow to yellow clear liquid with an assay of 99% minimum, and it is the standard long-chain anhydride hardener for making an epoxy system flexible without adding a separate plasticiser.
The commercial case is arithmetic rather than chemistry. DDSA has the lowest anhydride content of any liquid anhydride in ordinary supply – 27.04% by weight – so its equivalent weight is 269 and the dose at EEW 185 is 130.9 phr, almost twice the dose of tetrahydrophthalic anhydride. That is not a disadvantage; it is the point. Every kilogram of DDSA brings three and a half times as much hydrocarbon as a kilogram of THPA, and that hydrocarbon is what turns a brittle casting into a flexible one. DDSA is bought as hardener and flexibiliser in one drum.
Basic Information
| CAS Number | 26544-38-7 |
| Chemical name | 3-(Dodec-9-en-1-yl)oxolane-2,5-dione (dodecenylsuccinic anhydride) |
| Synonyms | DDSA; dodecenyl succinic anhydride; dodecenylsuccinic acid anhydride; tetrapropenylsuccinic anhydride (TPSA-likes are distinct); 2-dodecen-1-ylsuccinic anhydride |
| Molecular Formula | C16H26O3 |
| Molecular Weight | 266.38 g/mol |
| Anhydride groups per molecule | 1 |
| Theoretical anhydride group content | About 27.04% (C2O3 = 72.02 of 266.38) |
| Anhydride equivalent weight | 266.38 g/eq theoretical; 269.1 g/eq at 99% assay |
| Theoretical acid value | About 421.3 mg KOH/g |
| Theoretical iodine value | About 95.3 g I2/100 g (one alkenyl double bond) |
| PubChem CID | 6438029 |
| InChIKey | AMEIILZCUWMPEV-ONEGZZNKSA-N |
| Appearance | Pale yellow to yellow clear liquid |
| Chemical family | Alkenylsuccinic anhydride (long-chain, C16) |
Specifications
| Item | Value |
|---|---|
| Appearance | Pale yellow to yellow clear liquid |
| Assay | 99% min |
| Iodine value, colour, free acid, viscosity | Reported per lot; limits agreed against the application |
Two of those lines deserve attention at the enquiry stage. Colour matters because DDSA darkens on hot storage and on exposure to air, and a “yellow” reading at the top of the band is a different product on the bench than a pale yellow one. Free acid matters because this is the anhydride with the most to lose from water, for a reason set out below.
The Dose Is the Product
With 27% anhydride group, DDSA carries the fewest equivalents per kilogram of any hardener in the family, and the comparison is what makes it useful:
| Hardener | Working AEW | Equivalents per kg | phr at EEW 185, r 0.90 | Relative to THPA |
|---|---|---|---|---|
| Succinic anhydride, 99.5% | 100.6 | 9.94 | 48.9 | -34% |
| THPA, 85-43-8 | 152.15 | 6.57 | 74.0 | – |
| MTHPA, 41.0% min | 175.7 | 5.69 | 85.4 | +15% |
| DDSA, 99% | 269.1 | 3.72 | 130.9 | +77% |
Read the last column as the design rule. Replacing THPA with DDSA at equal r nearly doubles the hardener weight, and that increase is not waste – it is the flexibiliser, arriving inside the hardener. The consequence on the datasheet is a lower glass transition temperature, lower shrinkage, a longer pot life and a gentler exotherm, all from one substitution. The consequence in the plant is a mix that is more fluid and less reactive, which is usually wanted and occasionally not.
Blending for Intermediate Flexibility
Most formulators do not use DDSA alone. The usual route is a blend with a short-chain anhydride, and the blend equivalent weight is the harmonic mean of the two, weighted by mass:
| Blend | Blend AEW | phr at EEW 185, r 0.90 | Effect on the cured part |
|---|---|---|---|
| 100% THPA | 152.15 | 74.0 | The rigid reference |
| 70 THPA / 30 DDSA | 175.0 | 85.1 | Noticeably tougher, small Tg drop |
| 50 THPA / 50 DDSA | 194.4 | 94.6 | Flexible, still castable |
| 30 THPA / 70 DDSA | 218.7 | 106.4 | Elastomeric tendency |
| 100% DDSA | 269.1 | 130.9 | Maximum flexibility, lowest Tg |
The blend table is also the reason a mixing sheet has to be recomputed whenever the ratio changes: a 30% DDSA addition moves the dose from 74.0 to 85.1 phr, 15%, which is far outside the tolerance of a hand-weighed batch.
Water: The Most Expensive Hydrolysis in the Family
An anhydride opened by water is gone, and because DDSA is the heaviest molecule in the family it destroys the most material per kilogram of water taken up:
| Water picked up | DDSA destroyed | Dodecenylsuccinic acid formed | Free acid increase |
|---|---|---|---|
| 0.05% (0.5 kg/t) | 7.4 kg/t | 7.9 kg/t | +0.79 points |
| 0.10% (1 kg/t) | 14.8 kg/t | 15.8 kg/t | +1.58 points |
The diacid that forms is a real product in its own right – dodecenylsuccinic acid, CAS 29658-97-7 – which is why the acid is sold separately and why a hydrolysed DDSA drum can sometimes be sold on rather than scrapped. In an epoxy formulation it is not interchangeable with the anhydride: it is a diacid, so it reacts with epoxy through its carboxyl groups at a different rate and a different stoichiometry.
Free acid percent (as the C16H30O4 diacid, 286.41) equals acid value in mg KOH/g multiplied by 0.2552. The reverse conversion, water in kg per tonne from free acid percent, is to divide by 1.58.
The Iodine Value Is an Identity Check
DDSA carries one alkenyl double bond, so its theoretical iodine value is 95.3. That number is worth quoting on a certificate because the most common substitution in this corner of the market is the saturated analogue – dodecylsuccinic anhydride, C16H28O3, molecular weight 268.39 – which differs by two hydrogen atoms, has a theoretical iodine value of zero, and is dosed at almost exactly the same weight (131.9 phr against 130.9).
| Property | DDSA (26544-38-7) | DSA, dodecyl (2561-85-5, straight chain) |
|---|---|---|
| Formula / MW | C16H26O3 / 266.38 | C16H28O3 / 268.39 |
| Chain | Dodecenyl (one double bond) | Dodecyl (saturated) |
| Iodine value | About 95.3 | 0 |
| Working AEW at 99% | 269.1 | 271.1 |
| phr at EEW 185, r 0.90 | 130.9 | 131.9 |
A 0.7% dose difference and an iodine value difference of 95. Nothing on a mixing sheet will catch this swap, and nothing on the cured part will announce it either – until the oxidation and colour behaviour are compared in service. Ask for the iodine value.
Applications
- Flexible and toughened epoxy castings. The main use. Electrical potting where thermal cycling cracks a rigid system, and any casting that has to survive impact or differential expansion.
- Adhesives and laminating systems. Longer pot life, lower exotherm and better peel strength than a short-chain anhydride; used in structural and semi-structural adhesives.
- Blend component for intermediate flexibility. A 10 to 30% addition to a THPA or MTHPA system is the cheapest way to move a formulation from brittle to tough.
- Precursor to alkenylsuccinimide chemistry. The alkenyl chain plus the anhydride ring is the same starting geometry used for lubricant dispersants and corrosion inhibitors, where a polyamine is reacted onto the ring.
- Raw material for the corresponding diacid. Hydrolysis gives dodecenylsuccinic acid, used in its own right in rust-preventive and lubricant formulations.
- Paper and board chemistry. Alkenylsuccinic anhydrides are the reactive sizing chemistry for neutral papermaking; the DDSA chain length is one of the options, though the sizing grades are usually sold as such rather than as generic DDSA.
Handling and Storage
DDSA is a liquid supplied in steel drums and IBCs. Store indoors, out of sunlight, between 5 and 30 deg C, with the bung tight and the headspace under dry air or nitrogen for holds longer than a few weeks. Two degradation routes run in parallel in this product: hydrolysis, which raises the free acid, and oxidation of the alkenyl double bond, which moves the colour. Heat and open headspace accelerate both.
Warm the drum evenly if viscosity needs reducing – a drum heater is right, an open flame or a band heater on one side is not, because the free acid follows the hot spot. Handling: irritant, skin sensitiser, reacts exothermically with amines and alkalis, hydrolyses with water. Local exhaust ventilation, gloves and eye protection; absorb spills and dispose of as chemical waste.
Chemical Structure
CCC=CCCCCCCCC1CC(=O)OC1=O
One anhydride ring, two methylenes, and a twelve-carbon chain carrying a single double bond. Compare it with succinic anhydride (four carbons, no chain) and with dodecylsuccinic anhydride (the same chain, saturated): the ring does the curing, the chain does the softening, and the double bond does nothing at all during a cure – it is there for the chemistry that happens afterwards, or by accident.
Related Products
- Dodecylsuccinic anhydride (DSA), branched isomers – the saturated analogue
- Dodecenylsuccinic acid (DCSA), CAS 29658-97-7 – what DDSA becomes after hydrolysis
- Octenylsuccinic anhydride (OSA), CAS 42482-06-4 – the C12 homologue
- Nonenylsuccinic anhydride (NSA), CAS 28928-97-4 – the C13 homologue
- Succinic anhydride (SA), CAS 108-30-5 – the unsubstituted parent
- Anhydride curing agent dosage: phr, AEW and accelerators
FAQ
What is DDSA used for? Mainly as a long-chain anhydride hardener that makes an epoxy system flexible without a separate plasticiser, and as the alkenyl building block for succinimide and corrosion-inhibitor chemistry. It is also one of the chain lengths used in reactive paper sizing.
Why is the dose so much higher than for other anhydrides? Because only 27% of the molecule is the anhydride group. The working equivalent weight is 269, so at EEW 185 and r 0.90 the dose is 130.9 phr against 74.0 for THPA. The extra weight is the flexibiliser, and it is the reason DDSA is used at all.
How do I tell DDSA from dodecylsuccinic anhydride? Iodine value. DDSA is about 95.3; the saturated analogue is zero. The molecular weights differ by 2.01 and the doses by 0.7%, so nothing else in the specification will show the substitution.
Is DDSA the same as the paper sizing ASA? No. The sizing grades are alkenylsuccinic anhydrides sold against a sizing specification, typically with a defined chain-length distribution and a much tighter colour and hydrolysis requirement. DDSA can be a raw material for that chemistry, but a generic DDSA certificate does not qualify it as a sizing agent.
Can a hydrolysed drum be reclaimed? Not by drying. The anhydride ring does not close again at any temperature a plant will run, so hydrolysed DDSA is dodecenylsuccinic acid – a different product with a different equivalent weight. It has its own uses, but it is not DDSA.
Does DDSA cure epoxy on its own? Yes, with heat. It is slower and gentler than a short-chain anhydride and needs the usual accelerator and post-cure. Its long chain lowers the glass transition temperature, so it is normally blended rather than used alone where stiffness matters.
Contact PolyBlueChem for a current certificate of analysis with iodine value and free acid, a sample for a flexibility trial, and a quotation for drum or IBC supply.




