Methylhexahydrophthalic Anhydride (MHHPA), CAS: 25550-51-0

Methylhexahydrophthalic anhydride (MHHPA, CAS 25550-51-0) is the hydrogenated member of the methyl anhydride family: a colourless liquid at room temperature with a viscosity of 50 to 70 mPa.s at 25 deg C, a crystallisation point of -15 deg C or below, and no residual ring double bond. It is the liquid anhydride that does not yellow.

That last property is the commercial reason it exists. MTHPA and MHHPA are made from the same isoprene-maleic anhydride chemistry, and the only structural difference is that MHHPA has been fully hydrogenated. The price difference between them is small; the difference in cured colour after heat ageing is not, which is why MHHPA is the standard hardener for optical, optoelectronic and outdoor-exposure epoxy systems.

Basic Information

CAS Number 25550-51-0
CAS registry name Hexahydromethylphthalic anhydride (isomer mixture)
EINECS 256-356-4
Synonyms MHHPA; methylhexahydrophthalic anhydride; methyl hexahydrophthalic acid anhydride; hexahydro-3a-methyl-1,3-isobenzofurandione
Molecular Formula C9H12O3
Molecular Weight 168.19 g/mol
Anhydride groups per molecule 1
Anhydride equivalent weight 168.19 g/eq theoretical; about 171.6 g/eq at 98% assay, 169.9 at 99%
PubChem CID 3016472
InChIKey VYKXQOYUCMREIS-UHFFFAOYSA-N
Appearance Colourless clear liquid
Viscosity at 25 deg C 50 to 70 mPa.s (60 to 80 mPa.s on HHPA-blended grades)
Crystallisation point -15 deg C max
Ring double bond None (fully hydrogenated)
Chemical family Cycloaliphatic dicarboxylic anhydride, liquid, saturated

Why Two CAS Numbers Appear on the Certificate

MHHPA is bought under 25550-51-0, and 25550-51-0 is registered as hexahydromethylphthalic anhydride – the methyl position is not specified, so the number describes an isomer mixture rather than a single molecule. The single-isomer product is 4-methylhexahydrophthalic anhydride, CAS 19438-60-9, which has its own page and its own certificate.

That is the first reason two numbers appear. The second is the iodine value. Commercial MHHPA is made by hydrogenating MTHPA, and hydrogenation is never complete, so a lot always contains some tetrahydro material. The producer’s iodine value limit is what defines how much is allowed, and that is where the two grades come from:

Iodine value limit Tetrahydro content it allows What the grade is for
1.0 g I2/100 g max About 0.65% MTHPA equivalent Optical, optoelectronic and colour-critical work
10 g I2/100 g max About 6.5% MTHPA equivalent General casting and potting where colour is not the specification

The conversion is worth keeping: one per cent of MTHPA in an MHHPA lot raises the iodine value by 253.81 / 166.17 x 100 x 0.01 = 1.53. So an iodine value of 1.0 caps the tetrahydro residue at 1.0 / 1.53 = 0.65%, and a value of 10 caps it at 6.5%. The iodine value is therefore not a purity decoration; it is the number that says how much of the cheaper, yellowing component is in the drum.

When a certificate carries both 25550-51-0 and 11070-44-3, that is what it is describing: the MHHPA itself and the tetrahydro residue that the iodine value is controlling. Ask which limit the lot was released against.

Specifications

Three grades of MHHPA, differing in colour, iodine value and free acid:

Item Grade 1 Grade 2 Grade 3 (custom)
Appearance Colourless clear liquid Colourless clear liquid Colourless clear liquid
Colour, Pt-Co (Hazen) 20 max 30 max 10 max
Assay 98% min 98% min 99% min (active content)
Iodine value, g I2/100 g 1.0 max 10 max Not specified on the custom sheet
Viscosity at 25 deg C, mPa.s 50 to 70 50 to 70 50 to 70
Crystallisation point -15 deg C max -15 deg C max -15 deg C max
Free acid On request On request 0.2 or 0.5% max

Custom Blends With HHPA

MHHPA can be blended with hexahydrophthalic anhydride (HHPA, CAS 85-42-7) to a customer ratio – 7:3 is a common starting point. Both components are fully saturated, so the iodine value of the blend stays at 1.0 or below; what changes is the equivalent weight, the viscosity and the crystallisation behaviour.

Item Blend 1: MHHPA 25550-51-0 + HHPA 85-42-7 Blend 2: 4-MHHPA 19438-60-9 + HHPA 85-42-7
Appearance Colourless clear liquid Colourless clear liquid
Colour, Pt-Co (Hazen) 20 max 15 max
Iodine value, g I2/100 g 1.0 max 1.0 max
Viscosity at 25 deg C, mPa.s 60 to 80 60 to 80
Special custom option Colour Pt-Co 10 max, free acid 0.1 or 0.2% max

Two things follow from the numbers and both belong in the conversation before a blend is ordered. First, HHPA is the unmethylated analogue and is cheaper, so a blend is a cost lever as much as a property lever: at a 7:3 ratio by weight the blended equivalent weight is 100 / (70/168.19 + 30/154.16) = 163.7 against 168.19 for pure MHHPA, which is 2.7% less anhydride per hundred parts of resin. Second, HHPA crystallises between 34 and 38 deg C, so replacing 30% of the MHHPA with it removes the -15 deg C crystallisation point that the pure grades are bought for. That is why the blended sheets in the list above quote no crystallisation point: it is a property of the ratio, not of the product, and it has to be agreed per order.

The viscosity tells the same story from the other side: 60 to 80 mPa.s for the blends against 50 to 70 for the pure grades. The blend is thicker, not thinner, because it is closer to the crystallisation range.

Why Iodine Value Is the Specification That Matters

Colour, viscosity and crystallisation point can all be adjusted within a plant; the iodine value cannot, because it is set by how far the hydrogenation was taken. A 1.0 limit means the lot is essentially saturated; a 10 limit means about 6.5% of the material still carries a double bond that will react with oxygen and heat in service.

The visible consequence is yellowing. An unsaturated anhydride cured with a cycloaliphatic epoxy darkens under UV and under prolonged heat; the same system built on MHHPA does not, or does so far more slowly. This is the single reason the optical and optoelectronic grades are specified at 1.0 – and the reason a 10-limit grade should not be substituted when the part is visible.

The colour figure and the iodine value work together but are not the same statement. Pt-Co describes the liquid in the drum today; iodine value predicts what the cured part will look like in two years.

Equivalent Weight and Dose

phr = (AEW / EEW) x 100 x r, with the AEW taken from the assay rather than from the theoretical molecular weight:

Resin EEW AEW 171.6 (98% grade), r = 0.90 AEW 169.9 (99% grade), r = 0.90 AEW 163.7 (7:3 HHPA blend), r = 0.90
185 83.5 phr 82.7 phr 79.6 phr
200 77.2 phr 76.5 phr 73.7 phr
250 61.8 phr 61.2 phr 58.9 phr

Compared with the tetrahydro alternatives the numbers are close, and that is the point to watch: at EEW 185 and r = 0.90, MTHPA at a 41.0% anhydride group minimum needs 85.4 phr, 98% MHHPA needs 83.5 phr and THPA needs 74.0 phr. The step from MTHPA to MHHPA is 2.2% and can be absorbed by widening the ratio; the step from a solid THPA to either liquid is 13 to 15% and cannot.

Applications

  • LED and optoelectronic encapsulation. The main use of the 1.0 iodine value grade. Colourless liquid, no residual unsaturation, and a cured part that does not drift yellow under heat or UV.
  • Electrical casting and potting. Dry-type transformers, instrument transformers, sensors and power modules. The liquid form removes the melt stage; the saturated backbone keeps the colour stable through the cure cycle.
  • Outdoor and light-stable coatings and potting compounds. Where an anhydride-cured epoxy is exposed to daylight, the hydrogenated hardener is the difference between a part that holds its colour and one that does not.
  • Laminates and prepregs. Low viscosity and long pot life suit solvent-free impregnation; the absence of a reactive double bond keeps side reactions out of the cure.
  • Optical adhesives and optical potting. Where the cured material is in the light path and transmission has to survive the product life.

Handling and Storage

MHHPA is supplied as a liquid in drums and needs no melting. It is moisture sensitive in the usual anhydride way, and the liquid form has a larger exposed surface per unit volume than flake, so each opening is an exchange with the plant air. Keep drums closed and blank with dry nitrogen after partial use where free acid is specified at 0.2% or below.

Store above the crystallisation point. The -15 deg C limit means an unheated store in a cold climate is acceptable; a blend with HHPA is not, and will crystallise at a much higher temperature because of the HHPA content. Do not sample a drum that has been cold: melt it completely, homogenise, then sample.

Segregate from amines, alkalis, alcohols and water. Gloves and eye protection are the minimum – the anhydride is a skin sensitiser and the hydrolysis product is corrosive.

Packaging and Supply

Supplied in lined steel drums, with IBC and bulk options on request. Each lot ships with a certificate of analysis covering appearance, colour, assay, iodine value, viscosity, crystallisation point and free acid where specified. Blends are quoted by ratio, with the ratio and the crystallisation behaviour agreed per order. A safety data sheet accompanies the first shipment of each grade.

Chemical Structure

A cyclohexane ring carrying a methyl group and a fused five-membered anhydride ring, with no double bond in the ring. The single-isomer analogue is 4-MHHPA, CAS 19438-60-9.

Related Products

FAQ

Why does the certificate show two CAS numbers? 25550-51-0 is the MHHPA itself, registered without a specified methyl position. 11070-44-3 is MTHPA, the tetrahydro material left over from incomplete hydrogenation, and its level is what the iodine value limits.

What iodine value should I specify? 1.0 or below for anything visible, optical or exposed to light; 10 where the part is hidden and the colour is not a specification. The cost difference is small relative to the cost of rejecting a yellowed batch.

Is MHHPA better than MTHPA? For colour stability, yes, because it has no residual double bond. For cost and for heat resistance in a non-colour-critical casting, MTHPA is the usual choice. The comparison is set out in MTHPA vs MHHPA.

Can MHHPA be blended with HHPA? Yes, to an agreed ratio such as 7:3. The iodine value stays below 1.0 because both components are saturated, but the blend loses the low crystallisation point, so the ratio has to be agreed against the storage and transport temperature.

Can MHHPA cure epoxy at room temperature? No. Like the other anhydrides it needs heat, typically 120 to 160 deg C with an accelerator and a post-cure.

Contact PolyblueChem for a current certificate of analysis, a sample of any grade or blend, and a quotation for drum, IBC or bulk supply.

Scroll to Top