Nadic anhydride (NA, CAS 826-62-0) is the Diels-Alder adduct of cyclopentadiene and maleic anhydride: 5-norbornene-2,3-dicarboxylic anhydride, formula C9H8O3, molecular weight 164.16. It is a white crystalline solid with a melting point of 162 deg C or above, one anhydride group and one norbornene double bond held in a rigid bicyclic skeleton.
That rigid bridge is the commercial point. Nadic anhydride cures epoxy at a higher temperature and gives a stiffer, more heat-resistant network than the flat cycloaliphatic anhydrides, which is why it is specified in laminates, electrical insulation and high-temperature composites – and why, at 162 deg C, it needs a hot melt system rather than a drum pump.
Basic Information
| CAS Number | 826-62-0 |
| Chemical name | 5-Norbornene-2,3-dicarboxylic anhydride (endo form) |
| Synonyms | Nadic anhydride; NA; nadic acid anhydride; 3a,4,7,7a-tetrahydro-4,7-methanoisobenzofuran-1,3-dione; 5-norbornene-2,3-dicarboxylic acid anhydride |
| Molecular Formula | C9H8O3 |
| Molecular Weight | 164.16 g/mol |
| Anhydride groups per molecule | 1 |
| Anhydride equivalent weight | 164.16 g/eq |
| Theoretical iodine value | About 154.6 g I2/100 g (one double bond) |
| PubChem CID | 2723766 |
| Appearance | White crystalline solid |
| Melting point | 162 deg C min |
| Chemical family | Bicyclic cycloaliphatic dicarboxylic anhydride |
Specifications
Three grades are offered. They differ only in assay; appearance and melting point are held across the range.
| Item | Grade 1 | Grade 2 | Grade 3 (custom) |
|---|---|---|---|
| Appearance | White solid | White solid | White solid |
| Assay (HPLC) | 98% min | 99% min | 99.5% min or 99.8% min |
| Melting point | 162 deg C min | 162 deg C min | 162 deg C min |
Why the Melting Point Is the Specification
Nadic anhydride exists as endo and exo isomers, and the commercial product is the endo form obtained by the Diels-Alder route. The endo isomer melts at 162 deg C and above; the exo isomer melts well below that. A melting point on the certificate is therefore doing two jobs at once – it is the identity check for the product and the isomer check for the lot.
It is also the check that separates nadic anhydride from its most common substitution, methyl nadic anhydride (MNA, CAS 25134-21-8). MNA carries a methyl group, is a liquid at room temperature and is the product used where a pumpable anhydride is wanted. The two are not interchangeable: NA is dosed as a hot melt, MNA as a liquid, and the equivalent weights differ.
Equivalent Weight and Dose
The anhydride group content is fixed by the molecule rather than by a specification, because nadic anhydride is a single compound: 164.16 g/eq, with no concentration allowance to make. The dose follows the usual relation:
phr = (AEW / EEW) x 100 x r
| Resin EEW | r = 0.85 | r = 0.90 | r = 1.00 |
|---|---|---|---|
| 185 (standard DGEBA) | 75.4 phr | 79.9 phr | 88.7 phr |
| 200 | 69.8 phr | 73.9 phr | 82.1 phr |
| 250 | 55.8 phr | 59.1 phr | 65.7 phr |
Against the flat cycloaliphatic grades the step is modest but not zero: at EEW 185 and r = 0.90, nadic anhydride needs 79.9 phr where THPA needs 74.0 phr, about 8% more. Against a liquid MTHPA at the 41.0% anhydride group floor the gap reverses, because that product’s working equivalent weight is 175.7.
Applications
- High-temperature epoxy curing agent. Laminates, electrical insulation and structural composites where the cured part has to hold stiffness at temperature. The rigid bicyclic skeleton is what buys the heat resistance; the cost is a cure schedule that runs above the usual casting temperatures.
- Unsaturated polyester and vinyl ester resins. The retained norbornene double bond takes part in the styrene copolymerisation, and the bulky ring raises heat resistance and hardness.
- Coatings and adhesives. Used as a hard, heat-resistant building block in baking enamels and in adhesive systems that see elevated service temperature.
- Intermediate for norbornene derivatives. The same double bond makes it a starting point for hydrogenated and functionalised norbornane derivatives, including the methyl nadic anhydride family.
- Crosslinker and tackifier component. Where an anhydride is wanted for reactivity rather than as the main hardener.
Handling and Storage
Nadic anhydride is supplied as a solid, normally flake or crushed solid in polyethylene-lined bags, and it is dosed either as solid into hot resin or melted in a heated vessel. Two rules follow from the melting point. Melt at the lowest workable temperature – 170 to 180 deg C is enough – and do not hold the melt hot longer than the batch needs, because prolonged hot holding moves colour and free acid in the same direction. And keep the melt system dry: water in a 175 deg C anhydride hydrolyses it immediately, and the diacid formed does not go back.
The solid is moisture sensitive. Store sealed and dry, away from amines, alkalis, alcohols and oxidisers; the anhydride reacts exothermically with amines and hydrolyses with water. Handle with local exhaust ventilation, gloves, eye protection and a dust mask – the powder is irritating and the material is a skin sensitiser. Clean spills dry and never wash them into a drain.
Packaging and Supply
Supplied in polyethylene-lined bags or fibre drums, with big-bag or pallet quantities on request. Each lot ships with a certificate of analysis covering appearance, assay, melting point and, where agreed, free acid and colour. A safety data sheet accompanies the first shipment of each grade.
Chemical Structure
O=C1OC(=O)C2C3CC(C=C3)C12
The structure is a norbornene skeleton – a bicyclo[2.2.1]heptene ring – carrying a fused five-membered anhydride ring. There is no aromatic ring in the molecule, and that is the single most common error in secondary descriptions of this product.
Related Products
- 1,2,3,6-Tetrahydrophthalic anhydride (THPA), CAS 85-43-8
- 3,4,5,6-Tetrahydrophthalic anhydride (TMMA), CAS 2426-02-0
- Hexahydrophthalic anhydride (HHPA), CAS 85-42-7
- 4-Methyl tetrahydrophthalic anhydride (MTHPA), CAS 11070-44-3
- Anhydride curing agent dosage: phr, AEW and accelerators
- Methyl nadic anhydride (MNA), CAS 25134-21-8 – the same skeleton as a liquid
- Liquid anhydride hardeners for electrical casting: MNA, MTHPA and MHHPA
FAQ
What is the difference between nadic anhydride and methyl nadic anhydride? MNA (CAS 25134-21-8) is the methyl-substituted analogue and is a liquid at room temperature; nadic anhydride is a crystalline solid melting at 162 deg C and above. They serve the same application area but not the same dosing equipment, and the equivalent weights differ.
Why does the specification only give a minimum melting point? Because the number is being used as an identity and isomer check rather than as a purity ladder. The endo product melts at 162 deg C or above; a lot reading substantially lower contains exo isomer or acid, and neither the assay nor the appearance will tell you that.
Is nadic anhydride a solid or a liquid at room temperature? A solid, and a high-melting one. It has to be melted, which is the main practical difference between it and the liquid anhydrides such as MTHPA and MNA.
What does the assay grade change? The level of non-anhydride material – residual acid, exo isomer and low-level organic impurities. For a laminate or electrical application the 99% grades are the usual choice; 98% is workable where the resin system is forgiving and the cured colour is not specified.
Can nadic anhydride cure epoxy at room temperature? No. It is a high-melting solid and it needs a hot cure, typically well above the casting range used for liquid anhydrides, with an accelerator if the cycle has to be shortened.
Contact PolyblueChem for a current certificate of analysis, a sample of any of the three grades, and a quotation for bag, drum or big-bag supply.




