Dodecenylsuccinic acid (DCSA, CAS 29658-97-7) is the ring-opened form of dodecenylsuccinic anhydride: a C16 alkenyl succinic diacid, formula C16H28O4, molecular weight 284.39. It is an amber, clear, viscous liquid with an assay of 99% minimum, a theoretical acid value of 394.7 mg KOH/g and a theoretical iodine value of 89.3.
The commercial logic of this product is worth stating plainly, because it decides whether it is the right material or a mistake. Dodecenylsuccinic acid is what dodecenylsuccinic anhydride becomes when it takes up water – one mole of water per mole of anhydride, and the reaction does not reverse at any temperature a plant will run. It is therefore both a product in its own right, sold for chemistries that need a long-chain diacid rather than an anhydride, and the inevitable degradation product of a DDSA drum that has been open too long or stored too wet.
Basic Information
| CAS Number | 29658-97-7 |
| Chemical name | 2-(Dodec-1-en-1-yl)butanedioic acid (dodecenylsuccinic acid) |
| Synonyms | DCSA; dodecenylsuccinic acid; dodecenyl succinate; 2-dodecenylsuccinic acid; (E)-2-dodec-1-enylbutanedioic acid |
| Molecular Formula | C16H28O4 |
| Molecular Weight | 284.39 g/mol |
| Functional groups | 2 carboxylic acids, 1 alkenyl double bond |
| Acid equivalent weight | 142.20 g/eq (both carboxyls counted) |
| Theoretical acid value | About 394.7 mg KOH/g |
| Theoretical iodine value | About 89.3 g I2/100 g |
| PubChem CID | 5463970 (E isomer); 166693 for the record without defined stereochemistry |
| InChIKey | QDCPNGVVOWVKJG-VAWYXSNFSA-N |
| Appearance | Amber, clear, viscous liquid |
| Chemical family | Alkenylsuccinic diacid (long-chain C16) |
Specifications
| Item | Value |
|---|---|
| Appearance | Amber, clear, viscous liquid |
| Assay | 99% min |
| Acid value, iodine value, colour, water | Reported per lot; limits agreed against the application |
The acid value is the figure to put on the purchase order, because it is the functional content of the product. A certificate that reports assay but not acid value is reporting purity without reporting how much of the material will actually react.
An Acid Is Not an Anhydride
The two are related and they are not interchangeable, and mixing up their equivalent weights is the standard arithmetic error with this product:
| Measure | Dodecenylsuccinic acid | Dodecenylsuccinic anhydride |
|---|---|---|
| CAS | 29658-97-7 | 26544-38-7 |
| Formula / MW | C16H28O4 / 284.39 | C16H26O3 / 266.38 |
| Reactive groups | 2 carboxyls | 1 anhydride ring |
| Equivalent weight | 142.20 g/eq (acid) | 269.1 g/eq (anhydride, at 99%) |
| Equivalents per kg | 7.03 | 3.72 |
| Theoretical iodine value | 89.3 | 95.3 |
Read the equivalent weights carefully before using them. The 142.20 g/eq figure counts both carboxyl groups, which is the correct basis for esterification and for amidation; it is not automatically the correct basis for epoxy curing, because a carboxyl reacts with an epoxy group slowly and one of the two carboxyls may be sterically hindered by the chain. Epoxy formulators treat the acid as a co-curative or a modifier and develop the ratio on test rather than on stoichiometry alone.
For reference, the two products convert into one another exactly: one kilogram of water per tonne converts about 14.8 kg of the anhydride into about 15.8 kg of the acid, a mass balance that closes because the water becomes part of the molecule.
Why It Is Viscous
A C16 diacid with two carboxyls is a hydrogen-bonded liquid, and that is why the product is supplied as an amber, viscous material where the anhydride of the same chain is a mobile pale yellow liquid. The viscosity is temperature dependent and falls steeply on warming; most users warm the drum to 40 to 60 deg C to pump or pour it, which is a handling detail rather than a specification.
The colour is also inherent to the product rather than a defect: an amber reading on a diacid is normal, and it should not be compared with the pale yellow specification of an anhydride.
Applications
- Corrosion inhibitor and rust-preventive intermediates. Reaction with amines or polyamines gives amides and imidazolines built on a long hydrocarbon chain – the classic oil-soluble corrosion chemistry.
- Lubricant and fuel additive intermediates. The long-chain diacid backbone is used in dispersant and detergent additive synthesis where a succinic acid structure is wanted rather than the anhydride.
- Alkyd and polyester resin component. As the diacid in a condensation cook, it brings a C16 alkenyl side chain that plasticises the film and improves adhesion and water resistance.
- Ester and half-ester chemistry. Mono-esterification of one carboxyl gives an anionic or non-ionic surfactant intermediate, which is one of the higher-value uses of the molecule.
- Epoxy modification. Used as an acid co-curative or as a flexibiliser, with the ratio developed on test; the two carboxyls and the slow carboxyl-epoxy reaction make this a formulation exercise, not a stoichiometric one.
- Wetting and dispersing agents. Acid-functional anchors for pigment and filler dispersants in solvent-borne systems.
Handling and Storage
An amber viscous liquid in steel drums and IBCs. Store indoors, 5 to 30 deg C, sealed; it is far less moisture-sensitive than the anhydride because there is no ring left to open, which is one reason some formulators prefer the acid where storage conditions are poor. The alkenyl double bond is still there, though, so keep it out of sunlight and away from oxidisers if colour matters.
The material is acidic and mildly corrosive to skin and eyes; wear gloves and eye protection, and use local exhaust ventilation if the drum is warmed and fumes are noticeable. Absorb spills with inert material and dispose of as chemical waste. Do not mix with alkalis or amines in an open container.
Chemical Structure
CCCCCCCCC=CC(CC(=O)O)C(=O)O
A twelve-carbon alkenyl chain carrying one double bond, attached to a succinic diacid unit: two carboxyls on adjacent carbons, one methylene between them and the chain. Compared with the anhydride, the ring has been opened and a molecule of water has been added; nothing else about the molecule has changed, including the double bond that the iodine value measures.
Related Products
- Dodecenylsuccinic anhydride (DDSA), CAS 26544-38-7 – the anhydride form
- Dodecylsuccinic anhydride (DSA), branched isomers – the saturated analogue
- Octenylsuccinic anhydride (OSA), CAS 42482-06-4 – the C12 chain length
- Nonenylsuccinic anhydride (NSA), CAS 28928-97-4 – the C13 chain length
- Succinic anhydride (SA), CAS 108-30-5 – the parent compound
- Free acid, colour and storage of acid anhydrides
FAQ
Is dodecenylsuccinic acid the same as DDSA? No – one is a diacid and the other is the anhydride it forms on loss of water. CAS 29658-97-7 against 26544-38-7, molecular weight 284.39 against 266.38, acid equivalent 142.20 against anhydride equivalent 269.1. They are related by one molecule of water and are not interchangeable.
Why is it so viscous and so dark? Two carboxyl groups hydrogen-bond with each other, which thickens the liquid well beyond the anhydride of the same chain, and the amber colour is inherent to the diacid. Warm to 40 to 60 deg C to pump; do not judge the product against an anhydride’s colour specification.
Can I use it as an epoxy hardener? It can be used as an acid co-curative or modifier, but not by simply substituting it into an anhydride dose. The carboxyl-epoxy reaction is slow and needs heat and usually an accelerator, and one of the two carboxyls may be hindered. Develop the ratio on test.
Does the double bond react during cure? Not with the epoxy. The alkenyl bond is there for other chemistry – copolymerisation, addition, or as an oxidation site – and it is the reason the iodine value is worth specifying.
Is it a good way to use up a hydrolysed DDSA drum? Functionally yes, since it is the same molecule as the hydrolysis product, but commercially no: you would be relabelling an off-spec anhydride as a different product, and the buyer’s specification is for the acid made deliberately, with its own acid value and colour. Sell it as what it is, or use it internally.
How should it be stored? Sealed indoors, 5 to 30 deg C, out of sunlight. It has no ring to hydrolyse, so it is more forgiving than the anhydride, but the double bond still makes it sensitive to oxidation if colour matters.
Contact PolyBlueChem for a current certificate of analysis with acid value and iodine value, a sample for a corrosion or resin trial, and a quotation for drum or IBC supply.




