endo-Norbornane-2,3-Dicarboxylic Anhydride, No CAS

endo-Norbornane-2,3-dicarboxylic anhydride is the single-isomer, high-melting grade of the saturated bridged anhydride: same C9H10O3 skeleton as the mixed endo/exo product, but crystallised in the endo configuration alone, which pushes the melting point above 160 degC. It is bought for two reasons – a hard, non-caking solid for powder handling, and a guaranteed crystal form for processes that cannot tolerate a shifting melting range.

This product has no CAS number and is identified by name, formula and melting range. That makes the melting range and the isomer ratio the entire specification, and it makes the iodine value the only reliable way to prove you have not been shipped the unsaturated analogue.

Status: Specification below is the current production grade. Endo content by NMR, melting range and acid value are confirmed per lot on request.

Basic Information

CAS Number Not assigned – identified by name
Chemical name endo-Norbornane-2,3-dicarboxylic anhydride; endo-hexahydro-3,6-methanophthalic anhydride
Molecular Formula C9H10O3
Molecular Weight 166.17 g/mol
PubChem CID 96196 (skeleton entry)
InChIKey LQOPXMZSGSTGMF-UHFFFAOYSA-N
Chemical Family Bridged bicyclic alicyclic anhydride, saturated, endo isomer
Anhydride equivalent weight 166.17 g/eq

Specification

Item Requirement
Appearance White solid
Purity (assay) 98% min
Melting point 160 degC and above
Anhydride equivalent weight 166.17 g/eq
Acid value, after hydrolysis 675.5 mg KOH/g theoretical
Iodine value Effectively 0

Melting point will not tell you what you have – iodine value will

This is the most dangerous identification problem in the family, and it is worth stating plainly: the saturated endo product melts at 160 degC and above, and Nadic anhydride – the unsaturated compound, a different molecule with a different CAS (826-62-0) – melts in almost the same range. A melting point check cannot separate them. The table shows how close the physical figures sit:

Property endo-Norbornane anhydride Nadic anhydride Mixed endo/exo norbornane
CAS Not assigned 826-62-0 Not assigned
Formula / MW C9H10O3 / 166.17 C9H8O3 / 164.16 C9H10O3 / 166.17
Melting point 160 degC and above Approximately 165 degC 120 to 130 degC
Iodine value, theoretical 0 154.6 0
AEW 166.17 164.16 166.17

Two of the three columns melt within a few degrees of each other and two share the same molecular formula. The iodine value is the only column that separates them, which makes it the test to specify at goods-in. This is the same trap that runs through the anhydride family wherever a saturated and an unsaturated grade share a common name: the physical constants overlap and only one analytical number tells the truth.

Why pay for the single isomer

  • A melting range you can design around. A mixed endo/exo lot softens from 120 degC upward; the endo grade holds its form until 160 degC. For a powder premix, that is the difference between a free-flowing blend and a caked drum in a warm warehouse.
  • Consistent crystallisation. Single-isomer material gives one crystal form and one melting endotherm on DSC, which makes incoming inspection simple and batch-to-batch variation small.
  • Higher melt viscosity at the same temperature. The price of the higher melting point: the melt is thicker, so impregnation of tight windings needs a hotter pot or a longer cycle.
  • Slower dissolution. Where the mixed grade is blended into a solvent or a polyol, the pure endo grade takes longer – plan the cook accordingly.

Where it is used

Application Role Note
Powder premixes and dry blends High melting point resists caking in storage Keep bags sealed; moisture is the other caking route
Colour-stable castings requiring a hard network Saturated, rigid bridged ring, no yellowing site Hot-pot impregnation needs a heated line
Reference and calibration standards Single crystal form for DSC and XRD work Ask for the DSC trace with the lot
Blends where a defined melt is critical Fixed melting range gives reproducible gel time Confirm the blend’s crystallisation on cooling

Handling, packaging and supply

Store dry and cool; the higher melting point does not make the powder less hygroscopic, and a hydrolysed lot shows up as rising free acid and a falling acid value against the 675.5 mg KOH/g theoretical. Supplied in 25 kg net fibre drums with polyethylene liner, or 1 kg sample packs. Because no CAS is assigned, registration and customs paperwork needs name, formula and melting range – we provide a technical data sheet carrying all three, plus the iodine value that distinguishes this product from Nadic anhydride. COA covers appearance, assay, melting range and iodine value; endo content by NMR on request.

FAQ

How do I prove this is not Nadic anhydride? Iodine value. Both melt near 160 to 165 degC, so the melting point proves nothing; the saturated product reads close to zero and Nadic reads about 155.

What is the difference from the mixed endo/exo grade? Melting range, mainly: 160 degC and above against 120 to 130 degC, plus a harder melt and a single crystal form. Chemically both are C9H10O3 at 166.17 g/mol.

Can I use it in the same pot temperature as the mixed grade? No – the melt is thicker at the same temperature. Raise the pot temperature or extend the impregnation cycle, and watch free acid, which climbs faster at higher pot temperature.

Contact PolyBlueChem for a lot COA with iodine value and DSC trace, a sample and a quotation against your volume and destination port.

Related reading

Related Products

Scroll to Top