L-Cysteine hydrochloride is sold under two CAS numbers that look interchangeable on a quotation sheet and behave differently in a formulation. The anhydrous salt is CAS 52-89-1; the monohydrate is CAS 7048-04-6. They differ by one molecule of water, 18.0 g/mol, which is 11.4% of the monohydrate by weight – enough to move a dosage, a freight cost and a COA reading at the same time. This article is about telling them apart on paper, converting between them without arithmetic errors, and spotting the lots that are neither one thing nor the other.
Two products behind one name
The naming is the first trap. Suppliers quote “L-cysteine HCl”, “cysteine hydrochloride” and “L-cysteine hydrochloride monohydrate” for both CAS numbers, and some quotation sheets carry the anhydrous CAS while the material actually shipped is the monohydrate – which is the more common commercial form, because the anhydrous salt is hygroscopic and picks up water in storage anyway. The free base, L-cysteine (CAS 52-90-4), is a third product with a third molecular weight.
None of this is a mis-labelling scandal. It is the normal consequence of a salt that crystallises as a hydrate and dehydrates partially when dried. What matters is that the buyer knows which form the price refers to and which form the process needs.
The two molecules side by side
| Property | Anhydrous (52-89-1) | Monohydrate (7048-04-6) |
| Formula | C3H8ClNO2S | C3H10ClNO3S |
| Molecular weight | 157.62 | 175.63 |
| Chloride content (theoretical) | 22.49% | 20.19% |
| Water of crystallisation | 0 | 10.26% |
| Cysteine base equivalent | 76.9% | 69.0% |
| Thiol per kg | 6.34 mol | 5.69 mol |
| Behaviour in storage | Hygroscopic; tends to pick up water and approach the hydrate | Stable form; free moisture is the risk, not dehydration |
| Assay window (AJI 92 style) | 99.0 to 100.5%, on dried basis | 99.0 to 100.5%, on dried basis |
Read the last two columns of the middle rows as a single message: everything that matters downstream – chloride, base equivalent, thiol equivalents – differs by about 11%, and none of those differences shows up in the assay figure, because the assay is reported on the dried basis.
Chloride is the fingerprint, not a purity test
Most buyers treat the chloride line on a COA as an impurity check. On this product it is the identity check for the salt form. The theoretical chloride is 22.49% for the anhydrous salt and 20.19% for the monohydrate, a gap of 2.30 absolute percentage points – far wider than any analytical tolerance. A specification that reads 19.89 to 20.29% chloride is describing the monohydrate and nothing else.
Loss on drying alone is a weaker test, because a partly dried lot and a lot with free moisture can land on the same number from opposite directions. Chloride does not have that ambiguity: it reports the ratio of salt to water in the crystal, and free moisture does not change it. Two lines together, read as a pair, settle the question; either line alone can be argued with.
The assay basis trap: why the same lot shows two different numbers
A monohydrate lot cannot be 100% L-cysteine hydrochloride by mass and 10% water at the same time. If a COA reports assay 99.0 to 100.5% next to loss on drying 8.5 to 12.0%, the assay is on the dried basis. That is the normal convention for these monographs, and it is the number most suppliers quote, but the convention is rarely printed on the certificate.
The same lot, expressed on an as-is basis, contains 88.8 to 90.2% of L-cysteine hydrochloride. Both statements are true. The failure mode is a buyer comparing Supplier A (dried basis, 99.5%) with Supplier B (as-is basis, 89.8%) and concluding that A is a better product. A is not better; A is better documented. Always establish the basis before the comparison, and write the basis into the purchase order.
The same applies to dosage: 5.69 mol of thiol per kg as the monohydrate against 6.34 mol per kg as the anhydrous salt. A formulator who switches form and keeps the percentage constant has quietly cut the reducing equivalents by 10.3%.
Loss on drying and chloride are locked together
Because the two lines describe the same crystal, they constrain each other, and the constraint can be calculated. Take a lot as a mixture of monohydrate and anhydrous salt, and let w be the mass fraction that has lost its water of crystallisation. Chloride then reads 35.45 / (175.63 – 18.015 w) percent, while loss on drying reads 10.26 x (1 – w). Working both directions gives the table below.
| Loss on drying | What the lot actually is | Chloride to expect |
| 12.0% | Monohydrate plus 1.74% free moisture | 20.19% |
| 10.5% | Monohydrate plus 0.24% free moisture | 20.19% |
| 10.26% | Exactly the monohydrate | 20.19% |
| 10.0% | About 2.5% of the lot is anhydrous salt | 20.24% |
| 9.5% | About 7.4% anhydrous salt | 20.34% |
| 8.5% | About 17% anhydrous salt | 20.55% – outside the chloride window |
The table exposes something useful about the specification itself. A chloride ceiling of 20.29% corresponds to a loss on drying of about 9.7%; below that moisture level the lot is drying out and the chloride has already left the window. So the two limits cannot both be used at once: a lot at 9.0% loss on drying will fail the chloride line even though it passes the moisture line. If a COA shows a low loss on drying and a chloride of 20.2%, one of the two figures was not measured on that lot.
Converting a formulation between forms
| You have | You want | Multiply by | Because |
| Monohydrate | Anhydrous | 0.8975 | 157.62 / 175.63 |
| Anhydrous | Monohydrate | 1.1143 | 175.63 / 157.62 |
| Monohydrate | Free cysteine base | 0.6900 | 121.16 / 175.63 |
| Free base | Monohydrate | 1.4493 | 175.63 / 121.16 |
| Thiol equivalents, anhydrous to monohydrate | Same equivalents | 1.1143 | 6.34 / 5.69 |
Three worked cases that cover most reformulation requests:
- A recipe calls for 0.50% anhydrous L-cysteine hydrochloride and the warehouse holds the monohydrate: 0.50 x 1.1143 = 0.557%.
- A recipe is written around 0.30% free cysteine and purchasing buys the monohydrate: 0.30 x 1.4493 = 0.435%.
- A tender asks for 1 tonne of anhydrous and the supplier quotes monohydrate: 1.000 x 1.1143 = 1.114 t of monohydrate, or 1 t of monohydrate covers 0.8975 t of the anhydrous requirement.
The third case is where money is made or lost. A container of 18 tonnes of monohydrate carries about 1.85 t of water of crystallisation – weight that is paid for in freight, in duty and in warehousing, but which also buys storage stability. The right form therefore depends on the lane: short domestic flows that use material within weeks usually suit the anhydrous salt; long sea freight and slow-moving stock usually suit the monohydrate, because the anhydrous salt will pick up water on the way and land somewhere between the two forms anyway. When both forms are quoted, compare them on a dried-basis cost per kg of L-cysteine hydrochloride, not on cost per bag.
Why the free base is a third answer
L-Cysteine (52-90-4) is the cheapest form per mole of thiol, because you are not paying for hydrochloric acid or water of crystallisation. It is also the hardest to use: it is much less soluble in water than the hydrochloride, it oxidises faster in the solid state and in solution, and it has no acidity to buffer the system. That is why the hydrochloride dominates commerce – a 5% solution sits at pH 1.5 to 2.0, which is convenient for dissolving and inconvenient for any application that needs neutral pH. Formulations that must run near neutral (cold-wave systems are the classic case) start from the hydrochloride and neutralise deliberately, so that the pH is a controlled step rather than a property of the raw material.
What oxidation looks like before assay moves
The failure mode of every cysteine salt is oxidation of the thiol to a disulfide, forming cystine (CAS 56-89-3). Cystine is poorly soluble, so the first measurable sign is usually not a chemical number but turbidity: a clear 5% solution turns faintly hazy, and the transmittance test – not less than 98.0% in this grade – catches it before the assay does. On the COA the sequence to look for is transmittance falling while assay stays flat; on the bench it is a solution that no longer reads clear.
The rate depends on moisture, temperature and trace metals. Iron is limited to 10 ppm for this reason, but copper catalyses the same reaction more strongly and is not always specified – if a batch behaves oddly, ask for copper as well as iron. Storage practice follows: keep the material dry and cool, reseal opened packages, and prefer nitrogen blanketing on long sea freight.
A four-question checklist before approving a lot
| Question | What to look at | Red flag |
| 1. Which form is this? | Chloride and loss on drying, read as a pair | Chloride near 22.5% on a product sold as monohydrate |
| 2. On what basis is the assay? | Assay next to loss on drying | Assay 99%+ with 10% water and no basis stated |
| 3. Is it partly dried or blended? | Loss on drying below 9.7% against the chloride window | Low moisture with a mid-window chloride |
| 4. Is the thiol intact? | Transmittance, specific rotation, iron | Haze in solution, rotation drifting toward zero |
Question 4 has a second layer that is worth stating plainly: specific rotation is the only line that reports chirality. Assay, chloride, moisture and heavy metals can all pass on a lot that has partly racemised. If a rotation comes back at +2 deg when the window is +5.5 to +7.0, the lot is not weak – it is the wrong isomer mix.
Sourcing notes
The commercial form moves in 25 kg paper bags with a polyethylene liner, 25 kg fibre drums for humid destinations, and 500 kg or 1000 kg FIBCs for premix and industrial users. Ask for the batch COA with all lines, the SDS in the destination language, and – for anything touching parenteral use – bacterial endotoxin data. AJI 92, the specification most food-grade lots are sold against, is a commercial standard rather than a pharmacopoeia, so if your quality system requires a monograph, say which one at enquiry stage. Export documents normally classify the product under HS 2930.90, the organo-sulphur heading.
L-Cysteine hydrochloride monohydrate (CAS 7048-04-6) product page and current AJI 92 specification. For the applications side of the same molecule, see L-cysteine hydrochloride in bakery dough relaxation; for the derivatives, the site also covers N-acetyl-L-cysteine (CAS 616-91-1) and carbocisteine (CAS 638-23-3).