The alkenylsuccinic anhydrides are a homologous series with one variable: the length of the chain hanging off the anhydride ring. Six commercial products sit on that line – octenyl, nonenyl, dodecenyl, the saturated dodecyl version, the dodecenyl diacid on the other side of hydrolysis, and the C16 to C18 sizing grades sold to paper mills. Choosing between them is not a matter of opinion; it is a matter of counting carbons.
This page is the map. It gives the arithmetic that relates chain length to molecular weight, equivalent weight and dose, the three measurements that identify which member of the family is in the drum, and the reason some of these products have a CAS number and some do not.
The Series Follows 14n + 98
Add one methylene to the chain and nothing else changes: molecular weight rises by 14.03 and so does the equivalent weight, because there is still one anhydride group. With n carbons in the chain, an alkenylsuccinic anhydride is C(n+4)H(2n+2)O3 and its molecular weight is 14n + 98. The saturated version is C(n+4)H(2n+4)O3 and follows 14n + 100.
| Chain n | Product | CAS | Formula | MW (actual) | 14n + 98 |
|---|---|---|---|---|---|
| 0 | Succinic anhydride (saturated parent) | 108-30-5 | C4H4O3 | 100.07 | 100 (14n + 100) |
| 8 | Octenylsuccinic anhydride (OSA) | 42482-06-4 | C12H18O3 | 210.27 | 210 |
| 9 | Nonenylsuccinic anhydride (NSA) | 28928-97-4 | C13H20O3 | 224.30 | 224 |
| 12 | Dodecenylsuccinic anhydride (DDSA) | 26544-38-7 | C16H26O3 | 266.38 | 266 |
| 12, saturated | Dodecylsuccinic anhydride (DSA) | branched mixture unassigned; straight chain 2561-85-5 | C16H28O3 | 268.39 | 268 (14n + 100) |
| 16 | ASA sizing grade, low end | 70983-53-8 (mixture grade) | – | about 322 | 322 |
| 18 | ASA sizing grade, high end | 70983-53-8 (mixture grade) | – | about 350 | 350 |
The line is not a curiosity. It lets a buyer check a claim: if a supplier quotes a C12 chain and a molecular weight of 268, the product is saturated, not unsaturated, because the unsaturated C12 compound is 266.38 and the saturated one is 268.39. Two units is all the difference there is, and it is exactly the difference the iodine value measures.
One Column Decides Everything
Because the ring stays the same size while the chain grows, the anhydride fraction falls and the dose rises. That single trend is the whole selection logic:
| Product | Chain | Anhydride group | Working AEW (99%) | Equivalents per kg | phr at EEW 185, r 0.90 |
|---|---|---|---|---|---|
| Succinic anhydride | none | 71.97% | 100.6 | 9.94 | 48.9 |
| OSA | C8, straight | 34.25% | 212.4 | 4.71 | 103.3 |
| NSA | C9, branched | 32.11% | 226.6 | 4.41 | 110.2 |
| DDSA | C12, branched | 27.04% | 269.1 | 3.72 | 130.9 |
| DSA | C12, saturated | 26.83% | 271.1 | 3.69 | 131.9 |
| DCSA (diacid) | C12, two carboxyls | – | 142.20 g/eq acid | 7.03 | not an anhydride dose |
Read down the dose column and the dial becomes obvious. From OSA to NSA costs 6.7% more hardener; from NSA to DDSA costs a further 19%; DDSA to its saturated twin costs 0.7%. The first two steps buy real flexibility. The third buys nothing mechanical at all – it buys colour stability.
Three Measurements Identify Which One You Have
Nothing in this family can be identified by appearance, and assay does not help because every member is 98 to 99% of its own molecule. Three figures do the work:
| Measurement | What it answers | Values across the family |
|---|---|---|
| Iodine value | Is the chain saturated or unsaturated? | 120.7 (OSA), 113.2 (NSA), 95.3 (DDSA), 0 to 1 (DSA) |
| Molecular weight or AEW | How long is the chain? | 210, 224, 266, 268 – one step per CH2 |
| Appearance and colour band | Which side of the saturation line? | Unsaturated: pale yellow to yellow. Saturated: colourless to pale yellow |
The first two are quantitative and the third is a hint. In practice the iodine value is the cheapest and most decisive test, because the substitution that actually happens in this market is unsaturated for saturated, not one chain length for another:
| Substitution | Dose change | What shows it |
|---|---|---|
| DDSA to DSA (same chain, hydrogenated) | 0.7% | Iodine value: 95.3 to 0 |
| OSA to NSA (one carbon longer) | 6.7% | AEW and iodine value both move |
| NSA to DDSA (three carbons longer) | 19% | AEW, iodine value, dose |
| Any of them to a ring anhydride such as THPA | 40% to 77% | Dose, viscosity, cured stiffness |
Why Some of These Products Have No CAS
This is the detail that confuses buyers most, and it has a single explanation: the feedstock.
OSA is made from 1-octene, a straight-chain alpha olefin that is a single molecule. Its product has one structure, one CAS (42482-06-4) and one InChIKey – even though cis and trans geometry around the double bond means the commercial material is a mixture of two forms.
NSA and DDSA are made from propylene oligomers – the trimer (C9) and the tetramer (C12). Those oligomers are themselves mixtures of skeletal isomers, so the anhydride inherits the mixture. The CAS number quoted (28928-97-4 for NSA, 26544-38-7 for DDSA) describes a defined structure that the commercial product approximates rather than matches.
DSA is the hydrogenated version of DDSA, so it carries the same branched mixture – and once you hydrogenate a mixture of isomers, no single registration exists. The straight-chain compound is registered as 2561-85-5; the branched mixture is not.
The ASA sizing grades are built from internal olefins with a C16 to C18 distribution, so the product is a distribution rather than a compound. CAS 70983-53-8 is a mixture-grade registration with no PubChem structure record, which is an accurate description rather than a gap.
The practical rule: for a mixture-grade product, buy against the functional measurements – iodine value, acid value or anhydride content, colour, hydrolysis products – and treat the CAS as the entry point for the enquiry.
The Other Side of Hydrolysis
Every anhydride on this page has a diacid behind it, and one of them is sold as a product in its own right. Dodecenylsuccinic acid (CAS 29658-97-7, C16H28O4, 284.39) is what DDSA becomes when the ring opens, and it is the reason the free acid figure on a DDSA certificate is worth reading.
| Item | Anhydride, DDSA | Diacid, DCSA |
|---|---|---|
| Formula / MW | C16H26O3 / 266.38 | C16H28O4 / 284.39 |
| Equivalent weight | 269.1 (anhydride) | 142.20 (acid, both carboxyls) |
| Appearance | Pale yellow to yellow, mobile liquid | Amber, viscous liquid |
| Dose basis | Anhydride equivalent | Acid equivalent – and not the same chemistry against epoxy |
The diacid is not a substitute for the anhydride in an epoxy cure: a carboxyl reacts with an epoxy group slowly and one of the two carboxyls may be hindered. It is a product for corrosion inhibitors, ester and amide chemistry, and alkyd resins – and it is what a wet drum has become.
Where the Family Sits Against the Ring Anhydrides
The alkenylsuccinic anhydrides are one of two branches of the anhydride hardener market. This table places them:
| Type | Example | Working AEW | phr at EEW 185, r 0.90 | Cured character |
|---|---|---|---|---|
| Unsubstituted | Succinic anhydride, 108-30-5 | 100.6 | 48.9 | Hard, brittle, heat resistant |
| Cycloaliphatic, unsaturated | THPA, 85-43-8 | 152.15 | 74.0 | The general-purpose rigid reference |
| Cycloaliphatic, saturated | MHHPA, 25550-51-0 | 171.6 | 83.5 | Rigid, colour-stable, electrical |
| Bicyclic | Nadic anhydride, 826-62-0 | 164.16 | 79.9 | Highest heat resistance, solid |
| Bicyclic liquid | MNA, 25134-21-8 | 181.8 | 88.5 | High viscosity, class H casting |
| Long chain, C8 | OSA, 42482-06-4 | 212.4 | 103.3 | Mild flexibiliser |
| Long chain, C9 | NSA, 28928-97-4 | 226.6 | 110.2 | Intermediate flexibility |
| Long chain, C12 | DDSA, 26544-38-7 | 269.1 | 130.9 | Maximum flexibility |
Two facts fall out of that table. First, the jump from ring anhydrides to chain anhydrides is the largest step in the whole family – 40% to 77% more hardener – so a formulator crossing that line should expect to reformulate rather than substitute. Second, within the chain anhydrides the steps are small enough that a substitution looks harmless on paper, which is why the iodine value belongs on the purchase order.
Selection Table
| Requirement | Reasonable starting point | Why |
|---|---|---|
| Cure a rigid system, no flexibility wanted | A ring anhydride (THPA, MTHPA, MHHPA) | The chain anhydrides cost 40 to 77% more hardener for properties you do not want |
| Add toughness without losing heat resistance | OSA, or 10 to 20% of it in a ring system | The C8 chain is the mildest flexibiliser in the family |
| Survive thermal cycling in a potting compound | NSA | Middle dose, middle flexibility – the usual second trial after DDSA proves too soft |
| Maximum flexibility and impact resistance | DDSA | Longest chain, lowest glass transition, most hydrocarbon per kilogram |
| Same flexibility but no yellowing | DSA, saturated | No allylic hydrogen to oxidise; iodine value 0 to 1 |
| Acid-functional or corrosion chemistry | DCSA, the diacid | Two carboxyls, no ring to hydrolyse |
| Reactive sizing for neutral paper | ASA sizing grade | Different specification entirely – bought on machine performance |
| Food-contact starch modification | OSA, but a qualified grade | Same chemistry; the qualification is separate and not implied by an industrial certificate |
Buying Checklist
- Iodine value, as the saturation check, with the method stated. Theoretical values run 120.7 (OSA), 113.2 (NSA), 95.3 (DDSA) and 0 for the saturated grade.
- Molecular weight or anhydride content, to confirm chain length against the 14n + 98 line.
- Free acid or hydrolysis products, converted to a water budget: divide free acid percent by the factor for that member (0.2034 for OSA, 0.2159 for NSA, 0.2534 for DDSA).
- Colour with its basis – liquid Pt-Co, neat, not a solution reading.
- Isomer and feedstock statement, especially whether a “straight chain” claim is being made for a propylene-oligomer product.
- For sizing grades only: active content, carrier identity, hydrolysis limits and chain-length distribution.
FAQ
What is the difference between OSA, NSA and DDSA?
Chain length on the same anhydride ring: eight, nine and twelve carbons respectively. That gives molecular weights of 210.27, 224.30 and 266.38, working equivalent weights of 212.4, 226.6 and 269.1, and doses at EEW 185 of 103.3, 110.2 and 130.9 phr. Longer chain means more flexibility and more hardener by weight.
Why is the saturated product dosed almost identically?
Because hydrogenating a double bond changes the mass by only two hydrogen atoms, 2.01 g/mol. The dose moves 0.7%. What changes is oxidation stability and colour, not stoichiometry – so the iodine value, not the dose, is the specification that matters.
Which one is used for paper sizing?
The ASA sizing grades, built from C16 to C18 internal olefins. They are the same chemical family but a different product class: sold against emulsion behaviour, hydrolysis limits and machine performance rather than against an anhydride equivalent weight.
Can the epoxy grades be used for sizing?
The chemistry would work, but a generic epoxy-grade anhydride is not qualified for a paper machine: the chain distribution, the hydrolysis limits and the carrier are all part of a sizing specification and none of them are on an epoxy-grade certificate.
Why does the family have both single-CAS and mixture-CAS members?
Feedstock. A straight-chain alpha olefin gives one structure; a propylene oligomer gives a mixture of skeletal isomers; an internal-olefin blend gives a distribution. The CAS number follows the feedstock, not the application.
Is the diacid interchangeable with the anhydride?
No. Dodecenylsuccinic acid has two carboxyls and no ring, an acid equivalent of 142.20 against an anhydride equivalent of 269.1, and a different reaction against epoxy. It is a product in its own right, not a substitute.
References and Further Reading
- Homologous series basis: n-carbon alkenylsuccinic anhydride, C(n+4)H(2n+2)O3, molecular weight 14n + 98; the saturated analogue follows 14n + 100.
- Anhydride basis: C2O3 = 72.02 g/mol; anhydride content = 72.02 / MW; working AEW = MW / assay; phr = (AEW / EEW) x 100 x r.
- Iodine value basis: 253.81 g/mol for I2, one double bond per molecule; theoretical value = 253.81 / MW x 100.
- CAS and structures: OSA 42482-06-4 (CID 534543); NSA 28928-97-4 (CID 5354806); DDSA 26544-38-7 (CID 6438029); DSA straight chain 2561-85-5 (CID 98107); DCSA 29658-97-7 (CID 5463970); ASA 70983-53-8 (mixture grade, no structure record).
- PolyBlueChem: DDSA; DSA (saturated); OSA; NSA.
- PolyBlueChem: DDSA: flexibility, dose and the alkyl trap; ASA paper sizing and the minutes-long emulsion; succinic, maleic and glutaric anhydride compared; anhydride dosage in phr.
Contact PolyBlueChem for a current certificate of analysis on any member of the family, a sample for a flexibility trial, and a quotation for drum, IBC or tanker supply.