A bridged bis-anhydride is two phthalic anhydride units joined by a link in the middle. The link is the whole design variable: it decides how much the chain can bend, how well the polymer packs, how readily the dianhydride dissolves, and how much you pay. Four bridges dominate commercial supply – methylene, ethylidene, ether and bisphenol A – and the difference between them is not a grade, it is a different molecule with its own CAS.
Why bridge at all
PMDA has no bridge. Its two anhydride rings are fused to one benzene ring, so the unit is planar and rigid in every direction. That gives excellent heat resistance and modulus, and it also gives a polymer that barely dissolves, barely melts and comes out amber. A bridge fixes all three problems at once by breaking the fused aromatic system in the middle and allowing the two halves to rotate relative to one another.
What the bridge costs is stiffness. A bridged dianhydride gives a more soluble, more processable, paler polymer with a lower glass transition and a higher coefficient of thermal expansion. Every selection decision below is a position on that single trade.
The four bridges, side by side
| Dianhydride | CAS | Formula / MW | AEW | Bridge | Character |
| Methylenebis(phthalic anhydride) | 4200-79-7 | C17H8O6 / 308.24 | 154.12 | -CH2- | Shortest bridge; most crystalline; lowest cost of the bridged group |
| Ethylidenebis(phthalic anhydride) | 22197-42-8 | C18H10O6 / 322.27 | 161.14 | -CH(CH3)- | One carbon longer plus a methyl side group; less crystalline, more soluble |
| ODPA | 1823-59-2 | C16H6O7 / 310.21 | 155.11 | -O- | Ether hinge; excellent melt flow; highest cost of the three |
| BPADA | 38103-06-9 | C31H24O8 / 524.5 | 262.25 | Bisphenol A unit | Thermoplastic polyimide; large, expensive, flexible |
| PMDA (reference, no bridge) | 89-32-7 | C10H2O6 / 218.12 | 109.06 | Fused, planar | Rigidity and heat resistance; amber, low solubility |
| HPMDA (reference, alicyclic fused) | 2754-41-8 | C10H8O6 / 224.17 | 112.09 | Cyclohexane ring | Colourless; different mechanism from the bridged group |
Bridge length and what it does to the polymer
Between the methylene and the ethylidene bridge the structure changes by one CH2 – 14.03 g/mol, a 4.6% move in equivalent weight – and the physical consequences run in a consistent direction:
- Crystallinity falls. The methyl side group on the ethylidene bridge disrupts packing, so the material is less crystalline, dissolves faster and cakes less in storage.
- Tg falls slightly. A longer, more mobile link lowers the glass transition of the cured polymer; the effect is modest between CH2 and CH(CH3) and becomes substantial when the link is a full bisphenol A unit.
- Solubility rises. Both the dianhydride and its polyamic acid dissolve more readily with a less symmetric bridge, which is why the ethylidene grade is chosen when the methylene version will not stay in solution at the target solids.
- Dose moves by 4.6%. 75.0 phr against 78.4 phr at EEW 185, r = 0.9. Not enough to require re-validation, enough to require a check.
Push the bridge further and the trend continues: the ether link (ODPA) gives still more melt flow because the oxygen adds a second rotational degree of freedom, and the bisphenol A unit (BPADA) adds so much flexibility and free volume that the polymer becomes thermoplastic – it can be melted and re-melted rather than only cured.
The equivalent weight spread
The bridges do not just change behaviour, they change how much material goes into the pot. At EEW 185 and r = 0.9 for epoxy, or on a molar basis for polyimide:
| Dianhydride | AEW | phr at EEW 185, r 0.9 | Anhydride equivalents per kg | Relative mass for the same equivalents |
| PMDA | 109.06 | 53.1 | 9.17 | 1.00 (reference) |
| HPMDA | 112.09 | 54.5 | 8.92 | 1.03 |
| Methylenebis | 154.12 | 75.0 | 6.49 | 1.41 |
| ODPA | 155.11 | 75.5 | 6.45 | 1.42 |
| Ethylidenebis | 161.14 | 78.4 | 6.21 | 1.48 |
| BPADA | 262.25 | 127.6 | 3.81 | 2.41 |
The last column is the one to remember at quotation stage. A bridged dianhydride costs 40% more mass per equivalent than PMDA, and BPADA costs 2.4 times as much mass per equivalent – on top of a much higher price per kilogram. Neither is expensive because the supplier is greedy; both carry a lot of molecular scaffolding whose only job is to bend.
Handling: all of them hydrolyse
Every dianhydride in this table opens its rings with water and the acid value climbs. The arithmetic for a two-ring dianhydride of molecular weight M is: one gram of water consumes M/36.03 grams of dianhydride – 8.56 g for the methylene compound, 8.95 g for the ethylidene, 8.62 g for ODPA.
- Store sealed, cool and dry; use nitrogen blanketing for long sea freight and for anything electronic-grade.
- Let cold drums come to room temperature before opening, so condensation does not form on the powder.
- Check acid value on arrival against the theoretical figure (364.1 mg KOH/g for the methylene compound, 348.2 for the ethylidene). A low reading means rings are already open.
- Dissolve into dry solvent and keep the solution covered; polyamic acid solutions lose molecular weight on standing.
Choosing a bridge
| Requirement | Bridge of choice | Why not the others |
| Lowest cost while escaping PMDA rigidity | Methylene | Ether and bisphenol A cost more for the same direction of change |
| Dissolve at high solids, avoid caking in storage | Ethylidene | The methylene grade is more crystalline and dissolves more slowly |
| Melt processing, high flow | ODPA or BPADA | Methylene and ethylidene are solids that need a solvent or a hot melt above their melting range |
| Thermoplastic polyimide | BPADA | The others cure rather than melt, because the bridge is not long enough |
| Colourless film | None of these – use HPMDA | All four bridges leave the anhydride rings aromatic, so the charge-transfer colour remains |
That last row is the distinction most often missed: bridging improves processability but does not remove colour, because the rings that do the absorbing are still there. If pale or clear is the requirement, the aromatic backbone itself has to go – which is a different article.
Related reading
- Alicyclic and aromatic dianhydrides: choosing the backbone for a polyimide
- Anhydride curing agents and dianhydrides: the family selection map
- Anhydride curing agent dosage: phr from AEW and EEW
- Free acid, colour and storage: what hydrolysis does to an anhydride