Urea (Carbamide), CAS 57-13-6: Grades, Manufacture and Uses

Urea: One Molecule, Two Very Different Markets

Urea (CAS 57-13-6), also called carbamide, is the most concentrated solid nitrogen fertiliser in commercial use and, at the same time, the raw material behind AdBlue/DEF, the diesel exhaust fluid that keeps modern trucks inside nitrogen-oxide limits. Around 46.65% of its own mass is nitrogen, which is the theoretical ceiling for a solid nitrogen compound, and that number explains both the fertiliser economics and the purity arithmetic of the automotive grade.

The important commercial point is that agricultural urea and AdBlue-grade urea are the same molecule made in the same synthesis loop. What separates them is the impurity envelope, the final forming operation and the absence of formaldehyde treatment. A buyer who treats them as interchangeable because the CAS number matches is one dilution step away from a specification failure.

Chemical and Physical Properties

Property Value
CAS Registry Number 57-13-6
IUPAC name Urea (carbonyl diamide)
Common synonyms Carbamide; urea 46-0-0; carbonyldiamide
Molecular formula CH4N2O
Molecular weight 60.06 g/mol
Nitrogen content 46.65% theoretical (2 N per molecule)
Elemental composition C 20.01%, H 6.71%, N 46.65%, O 26.63% (calculated)
PubChem CID 1176
InChIKey XSQUKJJJFZCRTK-UHFFFAOYSA-N
SMILES C(=O)(N)N
Appearance White granules, prills or crystals
Melting point 132.7 deg C, with decomposition on prolonged heating
Density (solid) About 1.32 g/cm3
Bulk density About 0.72 to 0.85 kg/L, depending on prilling, granulation or crystallisation
Solubility in water Very soluble, about 1,080 g/L at 20 deg C (roughly 52% by mass)
Solution pH About 7.0 to 7.5 freshly prepared; rises as hydrolysis releases ammonia
Critical relative humidity About 72 to 75% at ambient temperature
Hazard classification Not classified as a dangerous good for transport; not flammable

Two of those rows are worth memorising. The 46.65% nitrogen ceiling is what makes every nitrogen figure on a urea certificate a purity statement rather than a strength statement. The 72 to 75% critical relative humidity is why urea cakes in an unventilated warehouse even when nobody has spilled water on it: above that humidity the material absorbs moisture from the air until it becomes sticky and then sets.

How Urea Is Manufactured

Urea synthesis is a two-reaction sequence carried out in one high-pressure loop, and every commercial process is a variation on how the unreacted intermediates are recovered and recycled.

The two reactions

Step 1: carbamate formation (fast, exothermic). Ammonia and carbon dioxide combine to ammonium carbamate:

2 NH3 + CO2 -> NH2COONH4

This step is fast and strongly exothermic, which is why the reactor needs heat removal rather than heat input.

Step 2: dehydration (slow, endothermic). Ammonium carbamate dehydrates to urea and water:

NH2COONH4 -> CO(NH2)2 + H2O

This step is the bottleneck: it is slow and endothermic, and it does not go to completion. A single pass through the reactor typically converts only part of the carbamate, so the process must recover unreacted ammonia and carbon dioxide and return them to the reactor. The plant’s overall yield depends on how efficiently that recycle is done, and that is what distinguishes the commercial process licences from each other.

The process families

Family Principle What it is good at
Total recycle, conventional Decompose the carbamate by heating and recycle everything back Simple concept; high steam demand for the decomposition and the water evaporation
CO2 stripping Strip the unreacted carbamate with fresh CO2 at synthesis pressure Low energy per tonne; the most widely installed design
Ammonia stripping Strip with ammonia at synthesis pressure Good energy performance without the CO2 compressor duty of the stripping designs
Isobaric double recycle Two stripping stages at synthesis pressure Lowest energy designs; more complex flowsheet

For a buyer, the process family matters less than what it does to two numbers on the certificate. Every process has to concentrate a urea solution, and the concentration and finishing stages are where biuret is made and where water is left behind.

Where biuret comes from

Biuret is not an impurity added from outside; it is a product of heating urea. Two urea molecules condense with the loss of one ammonia molecule:

2 CO(NH2)2 -> NH2CONHCONH2 + NH3

The arithmetic of that reaction is useful when reading a specification. Two moles of urea weigh 120.11 g and one mole of biuret weighs 103.08 g, so every kilogram of biuret formed consumes 1.165 kg of urea and releases 0.165 kg of ammonia. Biuret therefore records the thermal history of the melt: temperature, residence time and how many times the material has been through a concentrator.

That is the whole reason an AdBlue-grade plant is not simply an agricultural plant with better housekeeping. Lower biuret means lower temperatures in the evaporation section, which means more vacuum, bigger equipment and more energy per tonne. The premium on automotive urea is bought in the finishing section.

Finishing: Prilling, Granulation and Crystallisation

Urea leaves the synthesis loop as an aqueous solution. How it is turned into a solid decides its particle size, its mechanical strength, its dustiness and its biuret content.

Route How it works Typical product Trade-off
Prilling Melt is sprayed from the top of a tower and solidifies in falling air Small spherical prills, 1 to 2 mm Low capital; prills are weaker and dustier, and the melt is held hot
Granulation Melt or solution is sprayed onto recycled seed particles in a fluid bed or drum Larger, harder granules, 2 to 4 mm Higher capital and higher recycle ratio; best mechanical quality for blending
Crystallisation Urea is crystallised from solution, then dried Fine crystals, very low biuret Highest energy per tonne; the route used where the automotive limit has to be met

The agricultural particle size band of 1.18 mm to 3.35 mm with at least 93% inside it is a granulation specification. It exists so that urea granules can be blended with other fertiliser granules without segregating in a spreader or in a bulk truck: a blend of 2 mm urea and 4 mm diammonium phosphate separates on the way to the field, and the farmer applies a different ratio from the one that was ordered.

The Two Commercial Grades

The same product, specified twice.

Item Agricultural urea AdBlue / DEF grade urea
Total nitrogen, dry basis >=46.0% >=46.4%
Implied minimum urea content About 98.6% About 99.5%
Biuret <=0.9% <=0.75%
Moisture <=0.5% <=0.7%
Formaldehyde treatment Allowed, methylenediurea <=0.6% Not allowed; aldehydes <=10 mg/kg
Alkalinity as NH3 Not specified <=0.1%
Insoluble matter Not specified <=25 mg/kg
Phosphate as PO4 Not specified <=1.0 mg/kg
Calcium, magnesium, sodium, potassium, aluminium Not specified <=1.0 mg/kg each
Copper, zinc, nickel, chromium Not specified <=0.5 mg/kg each
Iron Not specified <=1.0 mg/kg
Particle size 1.18 to 3.35 mm, >=93% Judged on dissolution and insolubles, not on a fertiliser band

The nitrogen figure is a purity statement

Urea cannot exceed 46.65% nitrogen, so a 46.0% minimum means at least 98.6% urea and a 46.4% minimum means at least 99.5% urea. The 0.4 point difference between the grades is not extra nitrogen; it is 0.9% less of everything that is not urea. A certificate claiming 47% total nitrogen on a urea product is describing a product that cannot exist, and it is worth walking away from.

The biuret arithmetic that decides AdBlue grade

AdBlue is a 32.5% urea solution, close to the urea-water eutectic, which crystallises near minus 11 deg C. Making one tonne of the fluid consumes about 325 kg of urea, so every solid-specification figure is multiplied by roughly 0.325 on the way into the tank:

Solid urea figure Concentration in 32.5% AUS 32 Consequence
Biuret 0.75% (AdBlue grade) About 0.24% Margin against a 0.3% fluid limit
Biuret 0.9% (agricultural) About 0.29% Essentially no margin
Aldehydes 10 mg/kg About 3.3 mg/kg Margin against a 5 mg/kg fluid limit
Iron 1.0 mg/kg About 0.33 mg/kg Margin against a 0.5 mg/kg fluid limit
Insoluble matter 25 mg/kg About 8 mg/kg Margin against a 20 mg/kg fluid limit

Read the second row again. Agricultural urea at the legal biuret limit lands at 0.29% in the finished fluid, which is inside the fluid specification but with essentially no room for the biuret that the dissolution and storage steps can add. Add formaldehyde treatment and unspecified metals on top, and the case for a separate grade is arithmetic rather than marketing.

Why the transition metals are limited

The metal limits in the AdBlue column have nothing to do with agronomy. Copper, iron, zinc, nickel and chromium poison or foul the vanadium-based selective catalytic reduction catalyst, and calcium phosphate together with insoluble matter blocks the dosing injector and builds deposits in the mixer. A few milligrams per kilogram of the wrong metal is enough to raise ammonia slip or to trigger an engine derate on a vehicle that then gets diagnosed as a faulty sensor.

Applications

  • Nitrogen fertiliser. The dominant use worldwide. Urea hydrolyses in soil via urease to ammonium and carbon dioxide and then nitrifies to nitrate; surface application without incorporation loses nitrogen as ammonia, which is why placement and inhibitor choice are part of the agronomy rather than an add-on.
  • AdBlue / DEF raw material. Dissolved in demineralised water to 32.5% and injected into the exhaust stream ahead of the SCR catalyst, where it hydrolyses to ammonia that reduces nitrogen oxides to nitrogen and water.
  • Urea-formaldehyde resins. Condensed with formaldehyde for plywood, particleboard, MDF and laminating adhesives; the formaldehyde-to-urea molar ratio sets the emission class of the finished board.
  • Chemical intermediates. Starting material for melamine, dicyandiamide, cyanamide derivatives, hydroxyethyl urea, carbamide peroxide, and for the alcoholysis route to dimethyl carbonate.
  • Environmental and process uses. Denitrification in flue-gas and waste-water treatment, nitrogen source in fermentation media, and a component of de-icing and dust-suppression formulations.

Storage, Handling and Incompatibilities

Solid urea is hygroscopic with a critical relative humidity near 72 to 75%, so the correct storage is dry, ventilated and away from condensation. Bags should stay sealed, stacks should not be high enough to crush granules, and bulk piles should not sit directly on a concrete floor that wicks moisture. Most caked urea in the world was not rained on; it absorbed humidity slowly in a closed warehouse.

Molten urea is a time-at-temperature problem: above 132.7 deg C it slowly converts to biuret and releases ammonia, so every melting and prilling operation is designed around residence time. Aqueous solutions hydrolyse faster when warm, which is why AdBlue has a shelf life that shortens above about 25 deg C and why tanks are shaded.

Three incompatibilities deserve to be on the warehouse wall:

  • Hypochlorites and other chlorine-releasing biocides. Urea reacts with hypochlorous acid to form chloramines and, under the wrong conditions, nitrogen trichloride, which is explosive and acutely toxic. Urea and chlorine-releasing sanitisers must never share a bund or a spill tray.
  • Strong acids. Urea forms salts and hydrolyses; acid spills in a urea store generate heat and ammonia.
  • Nitrate salts. Urea-nitrate mixtures are hygroscopic and are regulated differently from urea in several jurisdictions; do not assume that a urea store is suitable for a nitrate store.

AdBlue-grade material has an extra handling rule: no contact with galvanised steel, copper alloys, zinc or untreated carbon steel, because trace metal pick-up can take a conforming lot out of specification in one transfer. Stainless steel, polyethylene and lined tanks are the standard materials.

Testing and Purchasing

Two nitrogen methods are used in this trade and they do not measure the same thing, which is the most common source of dispute on a urea certificate.

Method What it measures What it misses
Kjeldahl or Dumas (total nitrogen) All nitrogen in the sample, including biuret and free ammonia Cannot distinguish urea nitrogen from other nitrogen
Urease method (urea nitrogen) Nitrogen released as ammonia by urease, i.e. true urea Biuret is not hydrolysed by urease, so biuret nitrogen is excluded

The difference between the two is informative. Biuret is 40.8% nitrogen, so one percent of biuret contributes about 0.41 points of total nitrogen that the urease method will not see. A lot with 46.4% total nitrogen and 46.0% urea nitrogen is telling you that roughly one percent of its nitrogen is not urea nitrogen, and biuret is the first thing to check. Ask which method is on the certificate before comparing two suppliers’ numbers.

Biuret itself is measured colorimetrically by its reaction with alkaline copper tartrate, or by HPLC where a peak table is wanted. Water is Karl Fischer or loss on drying depending on the specification, and the AdBlue metals panel is ICP-OES or ICP-MS. For the metal panel the sampling matters as much as the analysis: a surface sample from a drum that was opened in a shed will pick up exactly the contamination the specification is trying to exclude.

FAQ

Why is urea 46% nitrogen when ammonia is 82%?

Because nitrogen content is quoted per unit mass of the product, and ammonia carries three hydrogen atoms for every nitrogen while urea carries a carbon and an oxygen as well. Per tonne shipped, urea delivers 466 kg of nitrogen against 822 kg for anhydrous ammonia, but ammonia is a pressurised gas and urea is a solid that can be bagged, blended and spread with ordinary equipment. The comparison that matters to a farmer is nitrogen per tonne handled, not nitrogen per molecule.

Can I blend agricultural urea with other fertilisers?

Yes, provided the particle sizes match and the urea is not wet. Urea blends with diammonium phosphate, monoammonium phosphate and potash are routine. The two rules are size matching to prevent segregation and dryness to prevent the caking reaction that turns a free-flowing blend into a solid block.

Why does urea lose nitrogen when it is surface applied?

Because urease in the soil hydrolyses it to ammonium carbonate, and ammonium carbonate decomposes to release ammonia gas at the surface. Incorporation, irrigation or a urease inhibitor reduces the loss; leaving prills on dry stubble in warm weather maximises it. The size of the loss depends on temperature, moisture, soil pH and how much crop residue is on the surface.

Is urea flammable or explosive?

Urea itself is not classified as flammable or as a dangerous good for transport, and it is not an explosive. It does decompose above its melting point, releasing ammonia and isocyanic acid, and it reacts dangerously with hypochlorites. The materials that cause explosions in the fertiliser trade are ammonium nitrate and urea-nitrate solutions, not urea.

What is the difference between prilled and granular urea?

Prilled urea is formed by spraying melt from a tower and letting droplets solidify in air, giving small, round, relatively weak particles. Granular urea is built up in a fluid bed or drum, giving larger, harder particles with better handling strength and a narrower size band. Granular is preferred for blending and for bulk handling; prilled is cheaper to make and adequate for direct application.

How long can urea be stored?

Dry, sealed and below the critical humidity, solid urea keeps for years with only slow change. The limit is not chemical decomposition but moisture pick-up and caking, both of which are reversible in principle and usually not in practice. AdBlue-grade material has a more demanding storage position because the metal and aldehyde specifications can be lost to the container rather than to time.

References and Further Reading

Disclaimer: this article describes industrial and commercial practice. Agricultural application rates, regulatory classification and automotive approvals depend on local rules and on the equipment manufacturer’s requirements, and must be confirmed by the user.

Contact PolyblueChem for a current certificate of analysis, a sample, and a quotation for agricultural or AdBlue-grade urea in bags, jumbo bags or bulk.

Scroll to Top