AdBlue-Grade Urea: AUS 32 Raw Material Specification

What AdBlue Actually Is

AdBlue is the trade name of a 32.5% aqueous urea solution injected into the exhaust of diesel vehicles to reduce nitrogen oxides. The generic names matter commercially, because each one belongs to a different regulatory system and a different market:

Name Where it applies Notes
AdBlue Europe and most export markets Registered trade mark of the German automotive industry association VDA; use of the name is licensed and tied to conformity
DEF (Diesel Exhaust Fluid) North America The API certification mark for the same fluid
AUS 32 ISO 22241 series "Aqueous Urea Solution 32.5%" – the neutral technical name used in specifications and shipping documents
ARLA 32 Brazil National standard designation for the same product

That table is not pedantry. A supplier who writes "AdBlue" on an export document for a market where the trade mark is licensed is making a claim it may not be entitled to make. Writing "AUS 32, AdBlue-grade" is accurate, describes the quality, and avoids the trade mark question.

Why 32.5%, and Not 40%

Concentration is not a marketing choice. The urea-water system has a eutectic near 32.5% urea by mass, and at that composition the crystallisation point is at its minimum, around minus 11 deg C. Two consequences follow.

First, the fluid survives a European winter in an unheated tank without freezing solid, and what does freeze is a slush that melts without permanently separating. Second, any solution stronger than the eutectic will precipitate urea crystals as it cools, and those crystals are exactly the deposits that block injectors and coat mixer walls. A supplier offering 40% urea to "give more ammonia per litre" is offering a fluid that will crystallise in service.

The density of the fluid at 20 deg C is about 1.09 kg/L, so a litre carries roughly 354 g of urea and 33.3 moles of ammonia equivalent on full hydrolysis. That is the number the dosing strategy works from, not the concentration on the label.

From Solid Urea to AUS 32: The 0.325 Dilution Factor

This is the single most useful calculation in the whole AdBlue supply chain. One tonne of 32.5% fluid contains about 325 kg of urea and 675 kg of demineralised water. Every impurity figure on the solid urea certificate is therefore multiplied by roughly 0.325 when it reaches the finished fluid:

Solid urea specification (AdBlue grade) Concentration in 32.5% fluid Commonly quoted fluid limit Margin
Biuret <=0.75% About 0.24% 0.3% Thin but real
Aldehydes <=10 mg/kg About 3.3 mg/kg 5 mg/kg Sufficient
Insoluble matter <=25 mg/kg About 8 mg/kg 20 mg/kg Sufficient
Phosphate as PO4 <=1.0 mg/kg About 0.33 mg/kg 0.5 mg/kg Thin
Iron, calcium, magnesium, sodium, potassium, aluminium <=1.0 mg/kg each About 0.33 mg/kg each 0.5 mg/kg each Thin
Copper, zinc, nickel, chromium <=0.5 mg/kg each About 0.16 mg/kg each 0.5 mg/kg each Comfortable

The fluid limits above are the values commonly quoted against the ISO 22241-1 quality framework; confirm each one against the current edition before writing it into a contract, because editions are revised. The important point is structural rather than numerical: the solid specification is not arbitrary, it is the fluid specification divided by 0.325 with a deliberate safety margin left in place. A buyer who understands that can audit any supplier’s numbers in a minute.

Now run the same calculation for agricultural urea. A 0.9% biuret content becomes about 0.29% in the fluid, which is inside the limit by a margin that the dissolution, filtration and storage steps can consume on their own. Add the fact that agricultural urea is typically formaldehyde-treated and carries no metal specification at all, and the conclusion is unavoidable: fertiliser urea is not a substitute feedstock, however clean the certificate looks.

The Standards Framework

Three groups of documents govern the trade, and they answer different questions.

Document Answers Who uses it
ISO 22241-1 What the fluid must contain – quality requirements and limits Producers, blenders, vehicle manufacturers
ISO 22241-2 How to test it – analytical methods Laboratories, auditors
ISO 22241-3 How to handle, store and transport it Logistics, distributors, tank operators
ISO 22241-4 How to refill – interface and dispensing requirements Filling stations, fleet operators
Vehicle manufacturer approvals Whether a specific product may be used with a warranty claim intact Fleets and OEM service networks

For a raw-material supplier the relevant document is the quality requirement plus the analytical methods, because that is what the solid urea specification has to map onto. For a blender, the handling and refilling documents decide tank materials, cleaning regimes and shelf-life statements.

What Each Limit Protects Against

Five impurity families do the work, and each one fails in a different way in the field.

Biuret

Biuret is a dimer formed by heating urea, and it does not hydrolyse to ammonia at exhaust temperatures the way urea does. It travels through the system and deposits. This is the impurity that most often separates a good fluid from a cheap one, and it is why the biuret limit is the first line any blender should check on an incoming solid lot.

Aldehydes

Formaldehyde and its condensation products come from anti-caking treatment, from resin residues in the plant, or from oxidation during storage. They foul the catalyst and they can form deposits in the injection nozzle. A specification that caps aldehydes at 10 mg/kg in the solid is doing two jobs: forcing the raw material to be untreated, and giving the blender a way to detect a treated lot.

Insoluble matter and phosphate

Insoluble particles and phosphate salts do not evaporate; they accumulate at the injector and in the mixer, where they form a hard scale that changes the spray pattern and then the dosing accuracy. Phosphate is limited as tightly as it is because calcium phosphate is one of the least soluble scales that can form in an alkaline urea solution.

Transition metals

Copper, iron, zinc, nickel and chromium deactivate the vanadium-based SCR catalyst and promote unwanted side reactions that consume ammonia without reducing nitrogen oxides. Iron also catalyses urea decomposition in storage, which is why the iron limit protects both the catalyst and the shelf life.

Alkalinity

A small alkalinity limit keeps the solution from drifting upward, where urea hydrolysis accelerates and ammonia is released. Ammonia release in a sealed tank raises the headspace pressure and the odour, and it changes the concentration of the fluid that is finally dosed.

Making AUS 32 From Solid Urea

The process itself is simple; the discipline is in the water and the materials.

  1. Water first. Demineralised water, usually reverse osmosis plus mixed-bed ion exchange, with conductivity and metal content checked per batch. Tap water, softened water and condensate all fail on metals or on alkalinity at the part-per-billion level this product works at.
  2. Dissolution under controlled temperature. Urea dissolves endothermically, so the batch cools as it dissolves; heating shortens the batch time but also accelerates biuret formation and hydrolysis. The usual compromise is warm water and a short residence time rather than hot water and a long one.
  3. Filtration. A fine filtration step, typically around one micron, removes insoluble matter that entered with the solid or formed during dissolution. Filters must be changed on differential pressure, not on schedule.
  4. Quality control on the batch, not on the tank. Density or refractive index confirms the concentration, and the metals panel confirms that nothing was picked up from the equipment.
  5. Dedicated equipment. Stainless steel, polyethylene or lined vessels; no galvanised fittings, no copper or brass valves, no carbon-steel pump bodies.

Storage, Transport and Shelf Life

AUS 32 is a dilute aqueous solution, and that has three consequences that surprise buyers.

It is mostly water, and you pay to ship it. One tonne of fluid contains about 675 kg of water and 325 kg of urea. Transporting solid urea and dissolving it near the point of use therefore moves roughly one third of the mass. That is why the international trade is in solid AdBlue-grade urea and the finished fluid is normally blended regionally, and it is the single most important commercial fact about this product.

It has a shelf life that depends on temperature. Cool storage keeps hydrolysis slow; sustained storage above about 25 deg C shortens the usable period, and repeated heating is worse than consistently warm. Storage out of direct sunlight, in a shaded or insulated tank, is standard practice rather than a refinement.

It freezes near minus 11 deg C, and that is acceptable. Freezing does not destroy the fluid provided it is allowed to thaw completely and mix before use. What destroys the fluid is partial freezing in a tank that is then drawn from, so the outlet pulls concentrated or diluted material rather than the homogeneous product.

Contamination in storage is almost always a materials problem rather than a chemical one: an unlined carbon-steel tank, a galvanised pipe, a copper fitting, a shared hose that previously carried something else. Because the metal limits are at the half-milligram-per-kilogram level, a single transfer through the wrong fitting can take a conforming batch out of specification.

Buying Solid or Buying Fluid

You are buying What to specify What to verify
Solid AdBlue-grade urea Nitrogen >=46.4%, biuret <=0.75%, aldehyde <=10 mg/kg, full metals panel, no formaldehyde treatment Certificate with element-by-element metals, plus a retained sample
Finished AUS 32 The ISO 22241-1 quality requirements, plus a conformity statement naming the edition Batch density or refractive index, metals panel, and evidence of the water quality used
Both, as a blender Solid specification plus an agreed fluid specification, plus a change-control clause Traceability from fluid batch to solid lot, and a re-test on the first blend of every new lot

The most common commercial failure in this market is a blender who buys on the nitrogen figure alone, because nitrogen says nothing about aldehydes or metals. The second most common is a buyer who accepts a certificate quoting "heavy metals <20 ppm" for a product whose entire specification lives at the 0.5 ppm level.

FAQ

Can I make AdBlue from agricultural urea if the biuret is low enough?

The biuret figure is only one of five requirements. Agricultural urea normally carries a formaldehyde-based anti-caking treatment, has no aldehyde or transition-metal specification, and is handled and stored in equipment that is not controlled for metal pick-up. A lot can pass on biuret and still fail on aldehydes or iron. Buy AdBlue-grade material.

Is diluted AdBlue better value if the price per litre is lower?

Dilution moves the concentration out of the eutectic range: it does not prevent crystallisation, it changes when and where it happens, and it reduces the ammonia delivered per litre so the dosing strategy under-doses and NOx conversion falls. There is no version of "water it down" that ends well in a vehicle with a NOx sensor.

Does frozen AdBlue have to be thrown away?

Not if it froze as a whole and is thawed completely and mixed before use. The problem case is a partially frozen tank that is drawn from, which delivers a stratified product. If in doubt, test density and biuret before putting the batch back into service.

Why are the metal limits so much stricter for AdBlue than for fertiliser?

Because the fertiliser is applied to a field and the AdBlue is applied to a catalyst that has to last the life of the vehicle. Copper, iron, zinc, nickel and chromium deactivate the SCR catalyst, and the effect is cumulative. A few milligrams per kilogram of the wrong metal is enough to raise ammonia slip and to trigger a fault.

Can the same truck deliver urea and AdBlue?

Only with a dedicated tank, liner or an approved cleaning and inspection regime, and the decision belongs to the blender’s quality system rather than to the haulier. Cross-contamination at the metal level is invisible at the point of transfer and expensive at the point of failure.

What documents should accompany a container of AdBlue-grade urea?

Batch certificate of analysis with the full metals panel, safety data sheet, non-hazardous transport statement, certificate of origin and packing list. For the finished fluid add a conformity statement against the named ISO 22241-1 edition, and for licensed markets a statement about whether the fluid is supplied under licence.

Related Reading

Disclaimer: this article describes industrial practice and commercial specifications. Vehicle approvals, warranty conditions and national regulatory requirements remain with the vehicle manufacturer and the operator; the numerical limits quoted against standards must be confirmed against the current edition of the relevant standard.

Contact PolyblueChem for AdBlue-grade urea with a full element-by-element certificate, samples, and bulk or bagged quotations.

Scroll to Top