Prilling vs Granulation vs Crystallisation: Urea Finishing

Why the Last Step Decides the Specification

Urea leaves the synthesis loop as a solution of urea in water with ammonia and carbon dioxide still dissolved in it. Everything that a customer measures on the finished solid – particle size, mechanical strength, dust, moisture and biuret – is set in the concentration, finishing and drying steps rather than in the reactor. Two plants with the same reactor licence can therefore ship products that pass completely different specifications.

The commercial consequence is that grade is bought in the finishing section. AdBlue-grade urea is not a purer molecule; it is a molecule that was finished at a lower temperature, held at temperature for less time, formed without formaldehyde treatment, and kept away from the metals that the automotive specification measures at the half milligram level.

The Three Finishing Routes

Route Mechanism Typical product Biuret position Strength and dust
Prilling Melt sprayed from a tower top, droplets solidify in rising or falling air Round prills, roughly 1 to 2 mm Melt is held hot at the tower; biuret can rise if the melt is held long Weaker particles, more dust and more caking tendency
Granulation Melt or concentrated solution sprayed onto recycled seed particles in a fluid bed or drum, building size layer by layer Irregular granules, 2 to 4 mm Recycle ratio is high, so the melt sees heat repeatedly; temperature control is the whole game Hardest, lowest dust, best for blending
Crystallisation Urea crystallised from solution, crystals separated and dried Fine crystals, narrow size Lowest, because the material never sits as a hot melt Fine and dusty; excellent purity; needs a separate handling design

Prilling

Prilling is the oldest and cheapest route: pump melt to the top of a tower, spray it, let the droplets solidify on the way down. It gives a round particle with good flow characteristics and a low capital cost, which is why prilled urea dominates older capacity. Its weaknesses are mechanical: prills are more fragile than granules, generate more fines, and their round shape and small size make them less ideal for blending with larger granular fertilisers.

For AdBlue grade, prilling has one specific liability. The melt is held hot in a large circulating system, and biuret formation is a function of temperature and time. A prilling tower can produce a low-biuret product only if the melt residence time is short and the temperatures are controlled tightly, which is exactly the kind of constraint that pushes producers toward crystallisation for the automotive grade.

Granulation

Granulation builds particles up in a fluid bed or a drum, spraying melt or concentrated solution onto a bed of recycled seed particles. The product is larger, harder and more uniform in size, which is why 1.18 to 3.35 mm agricultural urea is a granulation specification. It also has a high internal recycle ratio, so the material passes through the heat history several times; granulation plants are engineered around managing that, with tight temperature control in each pass.

Granulation is also where formaldehyde treatment is normally applied, because it improves granule strength and reduces caking. For an agricultural product that is a benefit. For an automotive product it is disqualifying, and the plant has to run untreated, which usually means a separate line or a campaign changeover with documented cleaning.

Crystallisation

Crystallisation avoids the hot melt altogether: urea is crystallised from a concentrated solution, the crystals are separated from the mother liquor and dried. Biuret formation is minimal because the material is never held as a melt, and the resulting product is very clean. The costs are real: more energy per tonne, a fine dusty product that needs different handling, and a size distribution that is not the fertiliser band.

That combination is precisely what AdBlue-grade raw material needs, which is why the automotive premium is a finishing premium rather than a chemical one. A producer who wants to serve both markets either runs two finishing lines or sells an agricultural product and a crystallised product from the same reactor.

Where Biuret Comes From, Precisely

Biuret forms by condensation of two urea molecules with the loss of ammonia. The reaction is driven by temperature and by residence time, and it is suppressed by keeping free ammonia present, because ammonia shifts the equilibrium back.

Control lever Direction Cost of using it
Lower temperature in evaporation and concentration Less biuret More vacuum, larger equipment, more steam or more cooling water
Shorter residence time in the melt Less biuret Smaller hold-up volumes, tighter control, less buffer against upsets
Higher ammonia partial pressure in the loop Less biuret More ammonia recycle duty, higher energy
Lower final urea concentration before finishing Less biuret More water to evaporate, worse energy per tonne
Crystallisation instead of melt finishing Lowest biuret Highest energy per tonne and a different product form

The arithmetic of the reaction is worth keeping in mind when comparing two certificates. Two moles of urea (120.11 g) become one mole of biuret (103.08 g) plus one mole of ammonia (17.03 g). Every kilogram of biuret therefore represents 1.165 kg of urea that has been consumed and 0.165 kg of nitrogen that has left as ammonia.

What Biuret Does to the Two Markets

In agriculture the limit is 0.9% because biuret above a certain level interferes with plant nitrogen metabolism, showing up as leaf damage on sensitive crops and in foliar applications. In automotive use the limit is 0.75% in the solid, which becomes about 0.24% in the 32.5% fluid, against a fluid limit near 0.3%.

The interesting part is why the automotive product tolerates a limit that is only slightly lower. The answer is that the automotive problem is not phytotoxicity but accumulation: biuret does not decompose to ammonia in the exhaust, so it deposits on the mixer and the catalyst face. Where agriculture has a tolerance, automotive has zero tolerance plus time.

Physical Form as a Fingerprint

An experienced buyer can learn something about the process from the product in the bag.

Observation Likely origin What to check
Small, round, uniform spheres Prilling Crushing strength, fines content, biuret
Larger, irregular, layered granules Granulation Size distribution, formaldehyde treatment, biuret
Fine crystalline powder, narrow distribution Crystallisation Dust behaviour, dissolution rate, insoluble matter
Mixed sizes, visible fines Poor screening or a blend Sieve test against the specified band
Whitened or chalky surface Moisture pick-up or surface treatment Moisture, caking behaviour, treatment level

This is a screening tool, not an identification method, but it does one useful thing: it tells a buyer whether the supplier’s description of the product matches the product. A bag described as granular that contains small round prills is a description problem worth resolving before it becomes a specification problem.

Energy, Cost and the Automotive Premium

Urea plants are judged on energy per tonne, and the finishing section is a significant part of that number. Crystallisation uses more energy than prilling. Granulation uses more than prilling in most configurations because of the recycle. Running untreated to meet an aldehyde limit costs strength and therefore dust and caking performance, which costs money further down the chain.

None of this makes automotive urea expensive in absolute terms; it makes it more expensive than agricultural urea from the same reactor, by an amount that reflects the finishing route, the yield loss, the separate logistics and the documentation. A buyer who is offered AdBlue-grade urea at agricultural prices should ask which of those four things has been left out.

Choosing a Route as a Buyer

Most buyers do not choose the route, they choose a supplier whose route happens to produce what they need. Three questions shorten the process.

  1. What form is the product, and what size band does it meet? A size analysis on a sample answers this in ten minutes and settles whether the product can be blended.
  2. What is the biuret, and what is the treatment? These two answers decide whether the lot can serve the automotive market at all.
  3. Is the automotive material run on a dedicated line or a campaign? Both are legitimate; a campaign changeover needs a documented cleaning procedure, and asking for it is a normal request rather than an accusation.

FAQ

Is prilled urea worse than granular urea?

Not worse, different. Prills are cheaper to make and fine for direct application. Granules are harder, larger and better for blending and bulk handling. The right question is which one the application needs, not which one is "better".

Can a prilling tower make AdBlue-grade urea?

It can, if the melt residence time and temperatures are controlled tightly enough to hold biuret below 0.75%, and if the plant runs untreated. Many producers find it easier to add a crystallisation line for the automotive grade than to constrain the tower, which is why the two forms often come from different parts of the same site.

Why is crystallised urea more expensive?

More energy per tonne, a fine product that needs different handling, and a lower yield per pass. The premium buys a lower biuret figure and the absence of a hot melt, which is exactly what the automotive specification needs.

Does formaldehyde treatment change the particle strength?

Yes. It improves granule strength and reduces caking, which is why it is common in agricultural granulation. Removing it for the automotive grade means the plant has to earn that strength through the granulation itself.

How is biuret controlled in storage, after the plant?

It is not, in practice. Storage at ambient temperature forms very little biuret. The biuret in a delivered lot was made in the plant, which is why the number on the certificate is a manufacturing fingerprint and a useful one.

Related Reading

Disclaimer: this article describes urea finishing technology at a general level. Individual plant configurations, energy figures and product forms vary by licensor and site, and must be confirmed with the producer.

Contact PolyblueChem for agricultural, granular and AdBlue-grade urea with the certificate and sieve data for the specific lot.

Scroll to Top