Methyl nadic anhydride is the hardener engineers specify when the part has to hold its shape at a temperature that would soften an ordinary casting. It is the methyl-substituted Diels-Alder adduct of cyclopentadiene and maleic anhydride, C10H10O3, 178.18 g/mol, a pale yellow liquid at room temperature with a viscosity between 170 and 300 mPa.s and a crystallisation point of -15 deg C or lower.
Two properties put it there. The first is the bicyclic norbornene skeleton, which is stiff enough to raise the heat deflection temperature of the cured network above what a single-ring cycloaliphatic anhydride gives. The second is that it is a liquid, which means it can be vacuum-pressure impregnated into a wound stator or cast under vacuum into a transformer coil without a melt plant. Nadic anhydride, the unmethylated parent, has the same skeleton and is a 162 deg C solid; the methyl group is the whole difference, and it is the reason MNA exists as a commercial product at all.
What MNA Is, and Why the Methyl Group Is the Product
The Diels-Alder reaction between a cyclopentadiene and maleic anhydride gives a norbornene-2,3-dicarboxylic anhydride. Run it with methylcyclopentadiene and the product carries a methyl group on the bicyclic ring; run it with cyclopentadiene itself and it does not. That one carbon changes the crystal packing completely. The unmethylated adduct packs into a lattice that melts at 162 deg C and above; the methylated adduct does not pack at all in the ordinary temperature range and arrives as a liquid.
The industrial consequence is bigger than the 14.02 difference in molecular weight. A solid hardener needs a melt vessel, a hot melt line and a temperature-controlled casting cell. A liquid hardener needs a drum pump and a day tank. For a plant already running vacuum casting, the second is a different factory from the first, and that is why MNA rather than nadic anhydride is the default in electrical impregnation even though the parent compound cures to a similar network.
CAS 25134-21-8 does not fix the isomer. It registers methyl-5-norbornene-2,3-dicarboxylic anhydride without specifying where on the ring the methyl sits, and it does not specify the endo/exo geometry either. The commercial product is a mixture, and the mixture ratio is what produces the viscosity band rather than a tolerance around a single value.
Chemical and Physical Properties
| Property | Value | Note |
|---|---|---|
| CAS | 25134-21-8 | Methyl-5-norbornene-2,3-dicarboxylic anhydride |
| Formula | C10H10O3 | 178.18 g/mol |
| Anhydride groups | 1 | 72.02 g of C2O3 per 178.18 g = 40.42% |
| Appearance | Pale yellow transparent liquid | Colour drifts with hot hold time |
| Viscosity at 25 deg C | 170 to 300 mPa.s | 4 to 10 times MTHPA at the same temperature |
| Crystallisation point | -15 deg C max | Winter logistics without heated transport |
| Assay | 98% min standard, 99% min custom | Anhydride content, not chromatographic purity |
| Theoretical acid value | 629.8 mg KOH/g | 112.22 g KOH per mole of anhydride |
| Theoretical iodine value | 142.4 g I2/100 g | One norbornene double bond |
| PubChem CID | 32802 | InChIKey KNRCVAANTQNTPT-UHFFFAOYSA-N |
The Number That Should Drive the Purchase: Equivalents per Kilogram
Anhydride hardeners are bought by weight and dosed by equivalent, and the two are not proportional across the family. Dividing one kilogram by the working equivalent weight gives the reactive equivalents in a drum, which is the only figure that lets you compare a drum of one hardener with a drum of another:
| Hardener | Working AEW | Anhydride equivalents per kg | phr at EEW 185, r 0.90 |
|---|---|---|---|
| Succinic anhydride, 99.5% | 100.6 | 9.94 | 48.9 |
| THPA (85-43-8) | 152.15 | 6.57 | 74.0 |
| Nadic anhydride (826-62-0) | 164.16 | 6.09 | 79.9 |
| MHHPA (25550-51-0), 98% | 171.6 | 5.83 | 83.5 |
| MTHPA (11070-44-3), 41.0% min | 175.7 | 5.69 | 85.4 |
| MNA (25134-21-8), 98% | 181.8 | 5.50 | 88.5 |
MNA carries the fewest equivalents per kilogram of any hardener in the family, 5.50 against 6.57 for THPA. A purchaser comparing price per tonne is comparing the wrong number: at equal r, a tonne of MNA buys 16% fewer equivalents than a tonne of THPA, and 3.4% fewer than a tonne of MTHPA. Everything else being equal, the cost per cured kilogram follows the equivalent count, not the invoice weight.
Reading the Specification
Viscosity
The band 170 to 300 mPa.s is wide because the isomer ratio is wide, and it is the number that decides whether the hardener suits the process. A vacuum-pressure impregnation line wants the low end because the resin has to flow into a winding and then out again under vacuum; a filled casting wants the high end because a thick hardener keeps silica in suspension through a long cast. Ask for the viscosity at 25 deg C on the certificate of every lot, and be aware that two lots at 175 and 295 mPa.s are both compliant product.
Crystallisation point
Minus 15 deg C or lower is what makes winter workable. It is not a purity figure; it is a logistics figure, and it is the one to quote to your forwarder. A drum that has crystallised in an unheated warehouse can be re-melted, but it has to be mixed as well as melted, because the anhydride and the free acid in it do not crystallise at the same rate, and re-melting a partly crystallised drum without mixing gives a homogeneous-looking liquid with a free acid figure that is not the batch figure.
Assay and free acid
Assay is an anhydride content by titration. It does not know the difference between an anhydride and hydrolysed material that has been counted wrongly, so it is always read together with free acid. On the custom grade the two come as a pair – 99% minimum assay with 0.05% maximum free acid – and that pairing is the point. See the water budget below.
Colour
Pt-Co is a visual comparison against a platinum-cobalt scale and it is not linear with the eye; it is the standard for liquids, and Gardner is not a substitute. On the standard grade colour is reported per lot rather than specified, because a product held in a warm tank for a week will move a step or two without anything having gone wrong chemically. Where the casting is visible or the part is inspected after impregnation, specify the custom grade.
The Water Budget Behind 0.05% Free Acid
An anhydride opened by water is gone: one mole of water consumes one mole of anhydride and leaves one mole of diacid, and the diacid does not re-close at any temperature a casting plant will run. For MNA, with a diacid molecular weight of 196.20:
| Water in the drum | MNA destroyed | Diacid formed | Free acid reading |
|---|---|---|---|
| 0.01% (100 ppm) | 1.0 kg/t | 1.1 kg/t | +0.11 points |
| 0.05% (500 ppm) | 4.9 kg/t | 5.4 kg/t | +0.55 points |
| 0.10% (1 kg/t) | 9.9 kg/t | 10.9 kg/t | +1.09 points |
Read it backwards and the custom grade becomes a procurement specification rather than a chemical one. A certificate reading 0.05% free acid is a statement that the drum has taken up no more than about 50 ppm of water since it was filled. That is a nitrogen-blanketed drum, a closed transfer and a tank that is not open to the room. If the process needs 0.05%, the nitrogen blanket is part of the purchase, not a detail of the plant.
The reverse conversion, for certificates that give acid value instead of free acid: free acid percent as C10H12O4 equals acid value in mg KOH/g multiplied by 0.1748.
Blending with Nadic Anhydride
MNA and nadic anhydride are the same skeleton with and without a methyl group, and blending them is how a plant gets a hardener that is partly solid and partly liquid without changing chemistry. The blend equivalent weight is the harmonic mean of the two, weighted by mass:
| Blend, NA : MNA by mass | Blend AEW | Change vs pure MNA | Behaviour |
|---|---|---|---|
| 0 : 100 | 181.8 | – | Liquid, 170-300 mPa.s |
| 30 : 70 | 176.1 | -3.1% | Liquid to thin slurry depending on temperature |
| 50 : 50 | 172.5 | -5.1% | Slurry; needs a melt or a heated line |
| 100 : 0 | 164.16 | -9.7% | Solid, 162 deg C melt |
Two things follow. The dose falls as the nadic fraction rises, which is arithmetic and easy to miss on a mixing sheet. And the crystallisation point is no longer a property of the product at all – it becomes a function of the blend ratio, so a blended grade specifies viscosity and assay and leaves the crystallisation point to a per-order agreement. That is the same reasoning that governs HHPA-blended MHHPA, and it applies to any anhydride blend.
Cure, Accelerators and Colour
Anhydride curing of epoxy is a ring-opening esterification and it needs heat: a typical schedule runs a gel at 90 to 120 deg C, a cure hold at 140 to 160 deg C and a post-cure above that where the heat deflection temperature matters. MNA’s rigid skeleton generally pushes the schedule toward the upper end of those bands relative to a tetrahydrophthalic system, and the network it produces is stiffer for the same reason.
Accelerators are standard practice rather than an option when the cycle has to fit an oven schedule. Benzyldimethylamine, 2-ethyl-4-methylimidazole and various quaternary ammonium salts are the usual families, dosed in the range of a fraction of a percent to about two parts per hundred of resin; the exact figure is a system property, not a hardener property, and has to be developed against the actual resin, filler and part thickness. What matters when buying the hardener is that acceleration shortens gel time and does not change the stoichiometry you calculated.
Colour is the other side of the retained double bond. The norbornene unsaturation that makes MNA useful in unsaturated polyester and vinyl ester systems is also the site that oxidises, so a mix held hot and open will yellow, and the yellowing is faster at higher hold temperature. The custom grade’s colour limit exists for parts where that is visible.
Applications
- Class H motor and generator impregnating varnish. The reference application. Vacuum-pressure impregnation of wound stators and rotors where the cured insulation has to hold electrical and mechanical properties at 180 deg C class temperatures.
- Dry-type transformer and instrument-transformer casting. Filled epoxy systems cast under vacuum, where the hardener has to keep silica in suspension and survive a slow gel without settling.
- High-voltage insulation. Bushings, insulators, switchgear and sensor encapsulation, usually with an accelerator and a filled system.
- Heat-resistant laminates and composites. Where the service temperature exceeds what a tetrahydrophthalic network holds and a solid hardener is impractical.
- Blend component. The liquid half of an NA/MNA blend, used to make a high-melting solid hardener pumpable.
- Unsaturated polyester and vinyl ester modification. The retained double bond copolymerises with styrene and raises heat resistance and hardness.
Storage, Handling and Winter Logistics
MNA is supplied in steel drums and IBCs. Store indoors between 5 and 30 deg C, out of sunlight, with the bung tight. For holds longer than a few weeks, keep the headspace under dry air or nitrogen; the product is not volatile but it is hygroscopic at the surface, and a part-full drum breathes with every temperature cycle.
The -15 deg C crystallisation point covers ordinary temperate and cold-chain logistics without heated transport. It does not cover unheated bulk storage through a hard winter in a cold climate, and it does not cover a drum left outdoors. If a lot has crystallised, re-melt gently and mix thoroughly before use.
Handling: skin and respiratory sensitiser, irritant, reacts exothermically with amines and alkalis, hydrolyses with water. Local exhaust ventilation at the transfer point, gloves and eye protection, no open transfer of hot material. Absorb spills and dispose of as chemical waste; never wash into a drain.
Buying Checklist
- Viscosity at 25 deg C, stated as a number. Not the CAS alone – 175 and 295 mPa.s are both compliant MNA and they do not run the same process.
- Crystallisation point and where it will be stored. The figure is a logistics specification; if the drum will stand in an unheated warehouse, say so at enquiry.
- Free acid, converted to water. Divide the free acid percentage by 1.09 to get the water equivalent in kg per tonne – 0.05% is about 0.046 kg, or 46 ppm – and check it against your nitrogen blanket.
- Assay and its basis. Confirm it is anhydride content by titration and ask what the certificate reports alongside it.
- Colour basis. Custom grade Pt-Co 30 or 50, read on the neat liquid, and reported per lot on the standard grade.
- Packaging and headspace. Drum size, liner, and whether the supplier nitrogen-blanks. This is what holds the free acid figure in transit.
- Isomer ratio if the process is viscosity-critical. Declared rather than certified, and the variable behind the band.
FAQ
Is methyl nadic anhydride the same as nadic anhydride?
No. Nadic anhydride (826-62-0) is the unmethylated adduct, a crystalline solid melting at 162 deg C and above. MNA (25134-21-8) is the methylated analogue, a liquid at room temperature with 181.8 g/eq working equivalent weight against 164.16. They share a skeleton and an application area; they do not share a dosing system.
Can MNA be substituted for MTHPA without changing the formulation?
No, although the dose is close: 88.5 phr against 85.4 phr at EEW 185 and r 0.90, a 3.6% step. What changes is processing and performance – viscosity roughly five times higher, a slower cure that wants more heat or more accelerator, a stiffer and more heat-resistant network, and a different colour behaviour. Treat it as a re-formulation, not a substitution.
Why is the viscosity so much higher than other liquid anhydrides?
Because of the bicyclic skeleton. MTHPA and MHHPA are single-ring structures that rotate freely; MNA carries a bridged ring system that resists rotation, and the mixture of isomers adds to that. The 170 to 300 mPa.s band is the price of the rigidity that gives the heat resistance. Warming to 50 to 70 deg C before pumping brings it into a usable range.
Can MNA cure at room temperature?
No. Anhydride cure is a heat-driven ring-opening reaction; MNA is no exception and its rigid skeleton usually wants more heat rather than less. Accelerators shorten the cycle but do not remove the oven.
Does MNA contain an aromatic ring?
No. The skeleton is a bicyclic norbornene with a fused anhydride ring and a methyl group. There is no benzene ring anywhere in the molecule, which is worth stating because it is the most common error in second-hand descriptions of the product.
What does the custom grade add over the standard grade?
Assay to 99% instead of 98%, a colour limit of Pt-Co 30 or 50, and a free acid limit of 0.05% instead of a reported figure. The free acid limit is the substantive one: it is a statement about the drum and its headspace, and it is the difference between a grade that can be held warm and a grade that has to be used promptly.
Is 98% assay 98% pure?
Not in the chromatographic sense. It means the titratable anhydride content is at least 98% of the theoretical 40.42%. A lot can be 98% on that basis while carrying a percent or two of diacid and a spread of isomers – which is why free acid, colour and viscosity are on the certificate as separate figures.
References and Further Reading
- CAS 25134-21-8: methyl-5-norbornene-2,3-dicarboxylic anhydride; PubChem CID 32802; InChIKey KNRCVAANTQNTPT-UHFFFAOYSA-N; formula C10H10O3, molecular weight 178.18.
- Anhydride group basis: C2O3 = 72.02 g/mol; 72.02 / 178.18 = 40.42% theoretical anhydride content; working AEW at 98% assay = 181.8 g/eq.
- Iodine value basis: 253.81 g/mol for I2 and one double bond per molecule gives 142.4 g I2/100 g theoretical.
- Hydrolysis basis: MNA + H2O gives the C10H12O4 diacid at 196.20 g/mol; 1 kg of water per tonne consumes 9.9 kg of MNA and generates 10.9 kg of diacid, a free acid rise of 1.09 points.
- PolyBlueChem: Methyl nadic anhydride product page; nadic anhydride product page; MTHPA product page.
- PolyBlueChem: Nadic anhydride: chemistry, production and applications; anhydride dosage in phr; free acid, colour and storage of acid anhydrides.
Contact PolyBlueChem for a current certificate of analysis, a pre-shipment sample and a quotation for drum, IBC or ISO tank supply.