Two Liquids, One Double Bond Apart
MTHPA and MHHPA are bought by the same people, for the same processes, from the same catalogue page, and at prices close enough that the quotation rarely decides the question. The structural difference between them is a single ring double bond: MTHPA has it, MHHPA has had it hydrogenated away.
That one bond does three things. It takes part in the cured network and raises the glass transition a little. It reacts with oxygen and heat over the life of the part, which is what turns a clear casting amber. And it is what makes MTHPA cheaper, because it skips a hydrogenation step. Choosing between the two is choosing which of those three effects the application cares about, and it is the most common specification decision in liquid anhydride work.
This page is that decision. The grade-level choice inside each product – crystallisation point, viscosity, colour, free acid – is a separate question, handled in MTHPA grades and on the MHHPA product page.
The Comparison
| Property | MTHPA | MHHPA | 4-MHHPA |
|---|---|---|---|
| CAS | 11070-44-3 | 25550-51-0 | 19438-60-9 |
| Formula / MW | C9H10O3 / 166.17 | C9H12O3 / 168.19 | C9H12O3 / 168.19 |
| Ring double bond | One | None | None |
| Isomer composition | Mixture, methyl position unspecified | Mixture, methyl position unspecified | Single isomer |
| Working AEW | 175.7 at the 41.0% anhydride group floor | 171.6 at 98% assay | 169.9 at 99% assay |
| phr at EEW 185, r = 0.90 | 85.4 | 83.5 | 82.7 |
| Viscosity at 25 deg C | 30 to 50 or 50 to 70 mPa.s | 50 to 70 mPa.s | 50 to 70 mPa.s |
| Crystallisation point | -15 or 0 deg C max depending on grade | -15 deg C max | -15 deg C max |
| Cured colour after heat and UV | Drifts amber | Stable | Stable |
| Glass transition | The higher of the two | A few degrees lower | A few degrees lower |
| Key quality figure | Anhydride group content | Iodine value | Isomer identity plus iodine value |
The two rows that decide most real specifications are the colour row and the dose row, and they pull in opposite directions: MTHPA is 2.2% heavier on the dose and noticeably worse on colour; MHHPA is the reverse except on cost.
What the Double Bond Actually Does
In the cured network: stiffness at temperature
The unsaturated ring is rigid, and rigidity in the hardener shows up as glass transition in the cured part. Remove it and the network relaxes a few degrees earlier. For a part that runs near its heat deflection temperature, a few degrees can be the difference between passing and failing a heat cycle – and it is the reason a formulator with a hot, hidden application does not automatically move to the hydrogenated grade.
In service: colour
The same bond that adds stiffness is the site that oxidation attacks. In a part exposed to heat or daylight, the sequence is well known: the double bond reacts, the network picks up oxygen, and the colour moves amber-to-brown. It is slow, it is cumulative, and it is irreversible. Hydrogenation removes that site, so an MHHPA part stays where it started.
The visible symptom is usually first noticed on a customer’s returned sample, which is why it is worth making the decision at the specification stage rather than after a qualification. If the part is decorative, visible through a housing, lit from behind, or carries light, MHHPA is not an upgrade – it is the correct product.
In the price: one process step
Hydrogenation costs money, but it is one catalytic step on a molecule that is already being made, so the gap between MTHPA and MHHPA is small compared with the gap between either of them and a speciality anhydride. The arithmetic that matters is not the price per kilogram but the cost of a rejected batch of yellowed parts.
How to Decide
| The application is | Take | Because |
|---|---|---|
| Hidden casting, hot service, cost-sensitive | MTHPA | Colour is not observed and the extra stiffness is wanted |
| Visible part, steady colour required | MHHPA, iodine value 1.0 | No double bond, no yellowing path |
| Optical path, lens or light guide | MHHPA or 4-MHHPA, iodine value 1.0, Pt-Co 10 | Colour is a yield parameter, not an aesthetic one |
| Qualified process that cannot absorb lot-to-lot drift | 4-MHHPA, single isomer | One reactivity instead of an average |
| Cost-driven, colour not specified, warm store | MHHPA/HHPA blend at an agreed ratio | Lower AEW and a cheaper component |
| Vacuum impregnation of fine gaps | MTHPA 30 to 50 mPa.s grade | The lowest viscosity in the family; MHHPA starts at 50 |
Two rows in that table are worth reading twice. The last one is the only real process advantage MTHPA retains: it is the only member of the family offered below 50 mPa.s, and in fine-gap impregnation that matters more than colour. And the blend row is a decision about logistics as much as chemistry – a blend that contains 30% HHPA loses the -15 deg C crystallisation point entirely, because HHPA crystallises between 34 and 38 deg C.
The Iodine Value: Reading the Hexahydro Side
MTHPA is judged on anhydride group content, because that is the figure that has to be converted into an equivalent weight. MHHPA is judged on iodine value, because that is the figure that says how much tetrahydro material is left in it.
The conversion is direct: one per cent of MTHPA in an MHHPA lot raises the iodine value by 253.81 / 166.17 x 100 x 0.01 = 1.53. So an iodine value limit of 1.0 caps the tetrahydro residue at 0.65%, and a limit of 10 caps it at 6.5%.
| Product | Iodine value | Residual unsaturation |
|---|---|---|
| MTHPA | About 152.8 theoretical | One double bond per molecule by design |
| MHHPA, optical grade | 1.0 max | About 0.65% MTHPA equivalent |
| MHHPA, general grade | 10 max | About 6.5% MTHPA equivalent |
| HHPA (unmethylated) | 1.0 max | Same limit, different molecule |
This is the same iodine value logic used for HHPA, where the limit of 1.0 caps a THPA residue at about 0.6%; the family has been using iodine value as its residual-unsaturation meter since long before colour became a specification. The arithmetic and the hydrolysis context are in HHPA: iodine value and colour stability.
Switching Between Them
A switch is easy to make and easy to get wrong in two specific ways.
- The dose moves by 2.2%, not zero. At EEW 185 and r = 0.90 the figure goes from 85.4 phr (MTHPA at the 41.0% floor) to 83.5 phr (98% MHHPA). That is inside most formulation tolerances, but it is not the same number, and a batch record quietly carried across is a small systematic error.
- The cure needs re-checking even when the dose does not. A hydrogenated hardener shifts the gel time and the glass transition a few degrees. In a thick casting that is a processing change; in an optical part it may be a qualification change.
The mistake that does real damage is the other direction: assuming that because MTHPA and MHHPA are close in dose they are interchangeable in a colour-critical part, and discovering the difference a year into service. The dose similarity is the trap – it makes the substitution look free when the cost is deferred.
Writing the Specification
Three lines cover the family decision and the grade decision together:
- Identity: “MHHPA, CAS 25550-51-0, iodine value 1.0 max, colour Pt-Co 20 max, crystallisation point -15 deg C max.” The CAS alone does not distinguish the mixture from the single isomer, so add “single isomer” and the 19438-60-9 CAS if that is what is wanted.
- Assay and the AEW behind it: “98% min” implies 171.6 g/eq. If the supplier quotes a dose, ask which equivalent weight it was calculated from.
- Packing and cold chain: lined drums, nitrogen blanket for the 0.2% free acid grades, and – for any HHPA blend – the storage temperature in writing, because the blend is a solid in an unheated store.
FAQ
Is MHHPA simply better than MTHPA?
It is better on colour and worse on glass transition and on cost. For a visible or light-exposed part the answer is yes; for a hot, hidden casting the unsaturation is doing useful work.
Can I mix MTHPA and MHHPA in one tank?
Physically yes, and the result behaves like an intermediate – which is the problem. Any iodine value between 1 and 152 can be produced by blending, and a blended drum has neither the colour stability of MHHPA nor the price of MTHPA. If a blended property is wanted, buy it as a specified blend rather than making it by accident.
Why is MHHPA judged on iodine value and MTHPA on anhydride group content?
Because the question is different. For MTHPA the useful figure is how much anhydride is present (it converts into the equivalent weight); for MHHPA the useful figure is how much unsaturation is left, because that is what predicts yellowing. Both are titration numbers and both belong on a certificate.
Does the single isomer cure faster?
Not systematically – the chemistry is the same. What changes is repeatability: with one isomer the gel time and the crystallisation behaviour stop moving from lot to lot, which is what a qualified optical process is buying.
Which is used for LED encapsulation?
MHHPA at iodine value 1.0, and 4-MHHPA where the process has been qualified against one reactivity. The application-side detail is in electronic and optoelectronic grade anhydrides.
Related Reading
- MHHPA product page: three grades and HHPA blends
- 4-MHHPA product page: the single isomer
- MTHPA product page: seven grades
- MHHPA: properties, iodine value and grades
- MTHPA: properties, grades and cure
- THPA vs 3,4,5,6-THPA vs HHPA: the solid end of the same family
- Anhydride curing agent dosage: phr, AEW and accelerators
- Liquid anhydride hardeners for electrical casting: MNA, MTHPA and MHHPA – the third option and the viscosity axis.